Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation instructions
Disconnect electrical power and electrical equipments before installing
dishwasher. should be done by qualified professionals. Failure to do so
can result in death or electrical shock.
Preparation
The installation position of dishwasher should be near the existing water
inlet tap and drain outlet and power socket. One side of the cabinet sink
should be chosen to facilitate the connection of drain hoses of the dish-
washer.
Positioning the appliance
Position the appliance in the desired location. The back should rest
against the wall behind it, and the sides, along the adjacent cabinets or
wall. The dishwasher is equipped with water supply and drain hoses that
can be positioned to the right or the left to facilitate proper installation.
Leveling of the dishwasher
It is important that the dishwasher is leveled. Use if necessary. a spirit
level inside the machine, both in depth and width and vertically on the
outside closed door.
The rear, right and left feet can be adjusted.
Dishwasher should be placed near the existing inlet and outlet hose and
power cable.
One side of the cabinet sink must be selected to facilitate the connection
of drain hoses dishwasher.
Note: Check the included installation accessories (aesthetic panel hooks,
screws)
Please read the installation instructions carefully Illustrations of the cab-
inet dimensions and mounting position for the dishwasher
Preparations must be made before moving the dishwasher to the instal-
lation site.
1
Select a location near the sink to facilitate the installation of inlet
and outlet hoses
2
If a dishwasher is installed in the corner of the cupboard, there
should be some space when opening the door.
Installation steps
1
Connect the inlet hose to the cold water supply
2
Connect the drain hose. Refer to diagram
3
Connect the power cord
4
Affix the condensation strip under the work surface of cabinet.
Please ensure the condensation strip is flush with edge of work sur-
face.
5
Place the dishwasher into position.
6
Level the dishwasher. The rear food can be adjusted from the front
of the dishwasher by turning the Allen screw in the middle of the
base of dishwasher use an Allen key. To adjust the front feet, use a
flat screw driver and turn the front feet until the dishwasher is level.
7
The dishwasher must be secured in place. There are two ways to do
this:
Normal work surface: Put the right(left) installation hook into the
slot of the right(left) side plane and secure it to the work surface
with two woodscrews.
Marble or granite work top: Bend the right(left) installation hook
into right-angle,and put it into the slot of the right(left) side plane
and secure it to the work surface with two woodscrews.
8
Bend the brackets of kick board according the depth to inserted to
the base , then fix the brackets to the kick board.
9
Insert the brackets to base of the dishwasher.
Leveling
Dishwasher must be level for proper dish rack operation and wash per-
formance.
1
Place a spirit level on door and rack track inside the tub as shown
to check that the dishwasher is level.
2
level the dishwasher by adjusting the three levelling legs individu-
ally.
3
When level the dishwasher, please pay attention not to let the dish-
washer tip over.
NOTE:
The maximum adjustment height of the feet is 50 mm.
Operation Instructions
Important: To get the best performance from your dishwasher, read all
operating instructions before using it for the first time.
Controlpanel
1.
Power Button and Indicator: switch On/Off the appliance,the indi-
cator light up when the power on.
2.
Washing Status Indicator: show you the washing progress.
Pre-Wash
Wash
Rinse
Drying
3.
Rinse Aid Indicator: light up when the dispenser needs to be refil-
led;
4.
Salt Indicator: light up when the dispenser needs to be refilled;
5.
Program knob: rotate the knob to select a washing program.
6.
Start/Pause button: press the button to start or pause the washing
progress .
Werbung
