Loading Staples - Makita ST113DSAJ Betriebsanleitung

Switch action
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
When not operating the tool,
depress the trigger-lock button from B side to
lock the switch trigger in the OFF position.
► Fig.3: 1. Trigger-lock button 2. Switch trigger
► Fig.4
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided.
To pull the switch trigger, depress the trigger-lock button
from A side.
After use, always press in the trigger-lock button from
B side.
Lighting up the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
► Fig.5: 1. Lamp
Pull the switch trigger or actuate the contact element to
light up the lamp. The lamp keeps on lighting while pull-
ing the switch trigger or actuating the contact element.
The lamp goes out approximately 10 seconds after
releasing the switch trigger and the contact element.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION:
Always make sure that the battery
cartridge is removed before carrying out any work
on the stapler.
Staples
CAUTION:
Do not use staples other than
designated in this manual or staples that appear
to be damaged, bent, rusty or corroded.
CAUTION:
Load the same type, size and
uniform length of staples when loading multiple
strips of staples in the magazine.
NOTICE:
Handle the staples and their box care-
fully. If the staples have been handled roughly,
they may be bent out of shape, causing poor
staple feed or jamming.
NOTICE:
Avoid storing the staples in a very
humid or hot place or place exposed to direct
sunlight.

Loading staples

WARNING:
When loading staples, always
make sure that the battery cartridge is removed
from the stapler. Unintentional firing may cause
personal injuries and property damage.
CAUTION:
After loading staples, make sure
that the sub magazine is surely closed. Falling
staples out of the magazine may cause an injury to
the operator or bystander, especially when working in
high locations.
1. Remove the battery cartridge.
2. Press the locking lever and slide the sub magazine backward.
► Fig.6: 1. Locking lever 2. Sub magazine
3. Load staples into the main magazine with their feet facing up.
► Fig.7: 1. Staples 2. Main magazine
4.
After loading staples, push back the sub-maga-
zine in place until it clicks.
To remove staples, follow the installation procedures in reverse.
Hook
CAUTION:
Do not hang the hook from the
waist belt. Dropping the stapler, which is caused by
the hook accidentally coming out of place, may cause
unintentional firing and result in personal injuries.
► Fig.8
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
► Fig.9: 1. Groove 2. Hook 3. Screw
OPERATION
Testing the safety system
WARNING:
Make sure all safety systems are
in working order before operation. Failure to do
so may cause personal injuries.
► Fig.10: 1. Trigger-lock button 2. Switch trigger
3. Contact element 4. Sub magazine
Test safety systems for possible fault before operation as follows.
1.
Unload staples from the tool and keep the sub
magazine opened.
2. Install the battery cartridge.
3. Only pull the switch trigger without touching the
contact element against the material.
4. Only touch the contact element against the mate-
rial without pulling the switch trigger.
If the tool operates in the case of 3 and 4 above, the
safety systems are faulty. Stop using the tool immedi-
ately and ask your local service center.
7 ENGLISH