Code Input; Code Search - Hama 00221062 Bedienungsanleitung

Warning - Batteries
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not burn batteries or heat them up.
• Never open, damage or swallow batteries or allow them to enter
the environment. They can contain toxic, environmentally harmful
heavy metals.
• Remove spent batteries from the product and dispose of them
without delay.
• Avoid storing, charging and using in extreme temperatures and
at extremely low atmospheric pressures (such as at
high altitudes).
• Ensure that batteries with damaged housings do not
come into contact with water.
• Keep batteries out of the reach of children.
4. First steps - Inserting the batteries
Note
• Use 2 type AAA batteries.
• Remove the battery cover on the underside of the remote control.
• Ensure the correct polarity (+/-) of the batteries and the battery
compartment.
• Insert the batteries.
• Reattach the battery cover on the remote control.
Note - code memory
This remote control saves the settings even during a battery change.
Note: Energy saving function
The remote control switches itself off automatically if a button is
pressed for longer than 15 seconds. This prolongs the life of the
batteries if the remote control is stuck in a place where the buttons
are pressed permanently, e.g. between sofa cushions.
Note:
Low battery display
• This remote control indicates when the batteries are getting low.
• If the status LED ashes 2 times after a button is pressed, the
batteries are weak and should be replaced promptly.
5. Setup
With the factory settings supplied, the remote control can control
approx. 90% of all SONY devices. There is no need to make any
settings. If the remote control does not work, select one of the setting
options mentioned in 5.1 and 5.2 below.

5.1 Code input

CODE list:
001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013,
014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026,
027, 028, 029, 030, 031, 032, 026, 027, 028, 029, 030, 031, 032
1. Press and hold [MUTE] and [POWER] simultaneously for approx. 3
sec. until the status LED lights up.
2. Enter the three-digit code from the code list. When all three digits
have been entered, the status LED goes out.
3. Test the functions of the remote control. If the function does not
work properly, try other device codes: [002], [003], [004], etc.
Note
If you have entered an invalid device code, the status LED ashes
twice and then shows a steady light again. To exit the device code
entry, press the mute button [MUTE].

5.2 Code search

1. Press and hold [MUTE] and [POWER] simultaneously for approx. 3
sec. until the status LED lights up.
2. Press the [PROG+ or PROG-] button to start the code search. With
each button press, the remote control sends a new code to your
TV. If your TV switches to a different programme, also test the
found device code using the [POWER], [VOL+], [VOL-], [MENU]
buttons and the number keys 0-9. If the functions work, press the
[MUTE] button to save the device code and end the search.
3. If the functions do not work, repeat the search by pressing the
[PROG+] button.
5.3 Code query
You can display the code currently used by the remote control:
1. First press and hold the mute button [MUTE], followed by
[POWER]. Release the two buttons when the status LED lights up
after approx. 3 sec.
2. Use the numeric keys to enter the numeric sequence 9-9-0. The
status LED ashes twice and goes out.
3. Use the numeric keys to enter the number 1. Count the number of
individual ashes of the status LED - this number corresponds to
the rst digit of the current device code.
Proceed accordingly for the 2nd and 3rd digits of the code:
2nd digit -> enter 2 -> count ashing signals
3rd digit -> enter 3 -> count ashing signals
If a digit of the device code is a 0, the LED does not ash.
2