Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes - EINHELL TC-SY 600 S Originalbetriebsanleitung

8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.1.1 Disconnecting and cleaning the gun
(Fig. 1-2, 11-15)
1. Unplug the spray gun from the mains power.
Press the trigger (5), so that the residual ma-
terial fl ows back into the container (12).
2. Unscrew the container (12) and empty the
residual material back into the material tin.
3. Clean the container (12) and the material
tube (11) with a bristle brush.
4. Pour solvent or water into the container.
Screw the container back on. Solvents with a
fl ash point above 55°C may not be used.
5. Reinsert the mains plug into the mains outlet
and turn on the paint spray gun. Set the max.
paint volume control (6) to the maximum fl ow
setting. Spray the solvent or water into a con-
tainer or rag, but never into the surroundings.
6. Repeat the procedure above until the clear
solvent or water exits from the nozzle (3).
7. Turn the paint spray gun off again and unplug
it from mains power.
8. Completely empty the container (12). Always
keep the container (12) free of residue and
check it for damage.
9. Use a rag soaked in solvent or water to clean
the outside of the paint spray gun and the
container (12).
10. Unscrew the air cap retaining ring (1) and
remove the air cap (2). Remove the nozzle
(3). Push the fl uid needle adapter (B) onto the
Anl_TC_SY_600_700_SPK13.indb 22 Anl_TC_SY_600_700_SPK13.indb 22
GB
fl uid needle (13). Twist and pull to remove the
fl uid needle. Clean the air cap retaining ring,
air cap, nozzle and fl uid needle with a bristle
brush and solvent or water.
11. Remove the fi lter cap (16) to clean the air inlet
fi lter. Remove the fi lter and clean it by blowing
out with air. Replace the fi lter and screw the
fi lter cap onto the gun. Do not operate the gun
without the fi lter.
12. Reinsert the fl uid needle. Pull the trigger and
insert the nozzle on the fl uid needle. While
inserting, ensure that the pins on the sides of
the fl uid needle point up/down and not right/
left. Pull the trigger while placing the air cap
on the nozzle and tightly fasten the air cap
with the air cap retaining ring.
13. Ensure that the paint spray gun is completely
dry before storing it.
14. Properly dispose of residual paint and
cleaning agents in accordance with local laws
and regulations. Residual paint and solvents
must be taken to a suitable collection point. If
you are not sure, ask the local council where
the nearest collection point is.
Warning!
Never immerse the paint spray gun in water or
other liquids. The housing may only be cleaned
with a dampened rag.
Note: If you use 2-component paint, you must
clean the gun immediately. Otherwise the paint
may dry inside the gun, causing an equipment
fault.

8.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 22 -
21.06.2023 10:56:22 21.06.2023 10:56:22