How To Use - Xiaomi X10 Benutzerhandbuch

How to Use

Connect with the Mi Home/Xiaomi Home App
This product works with the Mi Home/Xiaomi Home app*. Use the Mi Home/
Xiaomi Home app to control your device, and to interact with other smart home
devices.
Scan the QR code to download and install the app. You
will be directed to the connection setup page if the app is
installed already. Or search for "Mi Home/Xiaomi Home"
in the app store to download and install it.
Open the Mi Home/Xiaomi app, tap on the upper right,
and then follow the instructions to add your device.
* The app is referred to as Xiaomi Home app in Europe
9E651E75
(except for Russia). The name of the app displayed on
your device should be taken as the default.
Notes:
· This robot vacuum works with the Mi Home/Xiaomi Home app, and it supports Android 4.4 & iOS
10.0 or above.
· Only 2.4 GHz Wi-Fi networks are supported.
· The version of the app might have been updated, please follow the instructions based on the
current app version.
Reset Wi-Fi
When there is a connection loss between your phone and the robot vacuum
due to the router reconfiguration, wrong password or so, please follow the steps
below:
1. Open the cover of the robot vacuum so that you can see the Wi-Fi indicator.
2. Simultaneously press and hold the buttons and until you hear a voice
to indicate that the robot vacuum is waiting for the network configuration.
3. When the Wi-Fi indicator blinks, the Wi-Fi connection has been reset
successfully.
9
Start Cleaning
Press the button on the robot vacuum or tap the button in the app, and
the robot vacuum will clean all areas by first cleaning along edges and walls and
then in an S-shape pattern. Once the cleaning is complete, the robot vacuum
will automatically return to the auto-empty station to charge.
Method 1: Press the button on the robot vacuum to start cleaning.
Method 2: Tap the button in the app to start cleaning.
Notes:
· To ensure the robot vacuum can easily return to the auto-empty station after cleaning, allow the
robot vacuum to start from the auto-empty station, and avoid moving the auto-empty station
during a cleaning task.
· When using the robot vacuum for the first time, it is recommended to follow the robot vacuum
and remove any obstacles on the ground. If the robot vacuum may get stuck or scratch the
surface of the furniture in some areas, you can set restricted areas in the app to prevent the
robot vacuum from entering those areas.
Use the Vacuuming & Mopping Function
1. First dampen the mop pad and wring out excess water. Next, slide the edge of
the middle part of the mop pad into the middle slot of the water tank, and then
slide the edges on both ends of the mop pad into the slots on both sides of the
water tank. Lastly, attach the pad firmly onto the water tank.
① ② ③
2. Open the water tank plug, fill the water tank with tap water and insert the plug.
CAUTIONS:
· Do not add hot water to the water tank, as this may cause the tank to become deformed.
· To avoid clogging, do not add any cleaning agents or disinfectants to the water tank.
3. To install the mopping assembly, slide it into the back of the robot vacuum
until it clicks into place. Press the button or use the Mi Home/Xiaomi Home
app to start the cleanup. The robot vacuum will automatically recognize the
mopping assembly and begin mopping and dispensing water as needed.
CAUTIONS:
· To prevent the robot vacuum from entering a carpeted area, use physical barriers or set up virtual
walls or restricted areas in the app before mopping.
· The mop pad should be cleaned after every 30 minutes of use to ensure adequate water flow and
cleaning effectiveness.
④
4. After the robot vacuum finishes cleaning and returns to the auto-empty station,
press the release buttons on both sides of the water tank, and pull the mopping
assembly backward to remove it.
Note: When the robot vacuum is charging or not in use, remove the mopping assembly. Pour out
all remaining water in the tank, and clean the mop pad to prevent mildew or lingering odors.
10