Before Starting The Equipment - EINHELL 43.211.20 Bedienungsanleitung

Anleitung BT-JS 800 E_SPK1:_
GB
Important!
The vibration value changes according to the area of
application of the electric tool and may exceed the
specified value in exceptional circumstances.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Safety guard (Fig. 1/Item 15)
The safety guard (15) protects the user from
accidentally touching the saw blade (12) and
nevertheless enables you a free view of the
cutting area.
The safety guard (15) must always be fitted when
carrying out cutting work.
5.2 Changing the saw blade (Figs. 2-3/Item 12)
Important!
You can fit or replace saw blades without using
any other tools.
Pull the mains plug before you fit or replace a saw
blade.
Set the selector switch for pendulum action (8) to
position 3.
The teeth of the saw blade are very sharp!
Press the blade holder (14) and insert the saw
blade (12) into the blade holder (14) as far as the
stop (Fig. 2). The teeth on the saw blade must be
pointing forwards.
Allow the blade holder (14) to slide back to
starting position. The saw blade (12) must sit in
the guide roller (10) (Figure 3).
Check that the saw blade (12) is securely
mounted in the blade holder.
Follow the instructions above in reverse order to
remove the saw blade.
5.3 Installing the parallel stop (Figure 4/Item 11)
The parallel stop (11) enables you to saw parallel
cuts.
Undo the two locking screws (13) on the
soleplate (7).
Now slide the parallel stop (11) into the guides on
the soleplate (7). You can fit the parallel stop (11)
on either the left or right of the equipment.
The guide strip must always face downwards. Set
the required distance using the measurement
12
15.09.2008 13:31 Uhr Seite 12
scale on the parallel stop (11) and tighten the
locking screws (13) again.
5.4 Setting the soleplate for miter cuts (Figs. 5-6)
Use the Allen key (4) to loosen the screws for the
soleplate (18) on the bottom of the adjustable
soleplate (7) (Figure 5).
Pull the soleplate (7) slightly forward. The
soleplate can now be swiveled a maximum 45° to
the left and right.
If the soleplate (7) is pushed back to the rear
again, it will only function in the locking positions
at 0°, 15°, 30° and 45°, which are marked on the
graduated scale for the soleplate (9) (Figure 6).
Move the soleplate into the required position and
refasten the screw securing the soleplate (18).
However, the soleplate (7) is also easily set to
another angle. To do so, move the soleplate (7)
forwards, set the desired angle and refasten the
screw securing the soleplate (18).
5.5 Adapter for dust extraction system (Figure
7/Item 6)
Connect your jigsaw to a vacuum cleaner using
the adaptor for dust extraction (6). This will
provide excellent dust extraction on the
workpiece. The benefits are that you will protect
both the equipment and your own health. Your
work area will also be cleaner and safer.
Dust created when working may be dangerous.
Refer to the section entitled "Safety instructions".
Attach the adaptor (6) as shown in Figure 7, so
that it is securely seated in the housing.
Fit the vacuum tube of the vacuum cleaner onto
the adaptor opening (6). Check that the
connections are airtight.
6. Operation
6.1 ON/OFF switch (Fig. 8/Item 3)
To switch on:
Press the ON/OFF switch
To switch off:
Release the ON/OFF switch
6.2 Locking button (Fig. 8/Item 2)
You can lock the ON/OFF switch (3) using the locking
button (2) when the equipment is in operation. To
switch off the equipment briefly hold down the
ON/OFF switch (3).