Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
YOUR COFFEE MACHINE
6.2 Setting and changing the menu options
Below you will fi nd a summary of the menu options, which are
used to change and save the appliance's factory settings, as well as to
start programmes and look up information. You will fi nd detailed
information about this in this instruction manual.
•
Language (see 6.2.1 on page 24)
•
Water hardness (see 6.2.2 on page 24)
•
Temperature (see 6.2.3 on page 25)
•
Auto shut off time (see 6.2.4 on page 26)
•
Coff ee program (see 5.2.3 on page 13)
•
Cappuccino program (see 5.2.12 on page 20)
•
Hot water (see 5.2.7 on page 16)
•
Descale (see 6.2.5 on page 26)
•
Rinsing (see 6.2.6 on page 28)
•
Statistics (see 6.2.7 on page 28)
•
Reset to default (see 6.2.8 on page 28)
If OK is not pressed after you have changed a setting, the appliance
automatically returns to the coff ee mode after about 120 seconds
without saving the entries.
To go back to the coff ee mode, press the MENU button
6.2.1 Setting the language
You can choose between several languages. A diff erent language can be
selected as follows:
1.
Press the MENU button
until the menu option CHOOSE LANGUAGE appears. Confi rm
the menu option with the OK button.
2.
Th e language set appears on the display. Press the scrolling buttons
< or > until the desired language appears. When the desired
language is displayed, confi rm with the OK button.
6.2.2 Water hardness
A PLEASE DESCALE! message is displayed after the appliance has
been operated for a factory set period of time, calculated on the basis
of the maximum quantity of lime scale which may be contained in
the water used. If necessary, this period of operation can be extended,
making descaling less frequent, by programming the appliance based
on the actual lime content in the water used. Proceed as follows:
GB 24
6 Maintenance
twice.
and press the scrolling buttons < or >
YOUR COFFEE MACHINE
1.
Remove the "Total Hardness Test" strip (in front of your manual).
Th en dip it fully in the water for a few seconds. Remove it and
wait around 30 seconds until it changes colour and a number of
red dots are formed. For example, if there are 3 red squares on the
test strip, you must set the water hardness level to 3.
If you no longer have a water hardness test, you can fi nd the data
in the table below.
2.
Press the MENU button
until the menu option WATER HARDNESS appears. Confi rm
the menu option with the OK button.
3.
Th e display shows the current setting. Next press the scrolling
buttons < or > until the established hardness level is displayed.
Confi rm the selection with the OK button. Th e appliance is now
programmed to provide the descaling warning when necessary,
based on the actual hardness of the water.
Information on the hardness of the water in your area can be obtained
from the local water board. In the table below you can fi nd the water
hardness setting your machine requires.
German hardness
0 - 6 dH
7 - 13 dH
14 - 20 dH
> 21 dH
6.2.3 Setting the coff ee temperature
You can choose between three temperature levels. Th e coff ee
temperature levels are defi ned as follows:
•
TEMPERATURE LOW
•
TEMPERATURE MEDIUM
•
TEMPERATURE HIGH
6 Maintenance
and press the scrolling buttons < or >
French hardness
Water hardness
machine
0 - 11 fH
1
12 - 17 fH
2
18 - 36 fH
3
> 37 fH
4
GB 25
Werbung
Inhaltsverzeichnis
