Selecting The Operating Mode - Monacor SA-130DMP Bedienungsanleitung

SA-130DMP
➀
1 2
➁
5 Connection
Prior to connecting /disconnecting, switch off
all devices concerned .
1) For the connection of a microphone, use
the jack MIC (2): connect the microphone
via a 6 .3 mm plug or an XLR plug .
2) For the connection of stereo audio sources
with line signal level (e . g . MP3 player,
CD player, tape deck, radio, mixer, PC), two
inputs are available:
– 3 .5 mm jack AUX (3);
when this jack is connected, the mod-
ule "MP3 player / Bluetooth receiver / FM
radio" (4) will be muted .
– RCA jacks LINE IN (10);
L (white) = left, R (red) = right
3) The stereo connections PRE OUT and AMP
IN (11) can be used to insert an audio pro-
cessing device (e . g . equalizer, effect unit):
The signal, after the control VOLUME (8),
will be routed to the audio processing de-
vice via the output PRE OUT and returned
to the power amplifier of the SA-130DMP
via the input AMP IN .
a) Remove the two jumpers (one each for
the left channel and the right channel)
that interconnect the output PRE OUT
and the input AMP IN .
b) Connect the input of the device to be
inserted to the output PRE OUT .
c) Connect the output of the device to be
inserted to the input AMP IN .
4) Connect two speakers (minimum im-
pedance: 4 Ω) to the terminals SPEAKER
OUT (12): Connect one speaker to the
channel RIGHT and the other to the chan-
nel LEFT . Observe the polarity (connect the
marked core of the respective speaker cable
to "+") . Use either the screw terminals or
the banana jacks to make the connections .
Note: When connecting more than two speakers,
make sure that the total speaker impedance per
channel is at least 4 Ω; otherwise, the amplifier
may be damaged . Contact an expert if you have
any questions .
5) Connect an FM antenna to the jack FM
ANTENNA (14) . With good reception con-
ditions, the wire antenna provided can be
used .
6) For power supply, connect the mains cable
provided to the mains jack (13) first and
then to a mains socket (230 V / 50 Hz) .
8
3
10 11
6 Operation
CAUTION Never adjust the amplifier to a
To prevent switching noise, always switch on
the devices connected before switching on the
amplifier and always switch off the amplifier
before switching off the other devices .
1) Before switching on the amplifier for the
first time, turn the total volume control
VOLUME (8) to the left stop .
2) Use the POWER switch (1) to switch on the
amplifier .
3) Turn up the control VOLUME (8) to adjust
the total volume desired; for each audio
source to be heard, adjust the volume by
means of the appropriate control:
– control MIC LEVEL (5) for the microphone
connected to the input MIC (2)
– control LINE LEVEL (7) for the device con-
nected to the input LINE IN (10)
– control AUX / MP3 LEVEL (6) for the de-
vice connected to the input AUX (3) or,
when the input AUX is not used, for the
module "MP3 player / Bluetooth receiver /
FM radio" (4)
Note: The basic volume of the module can be
additionally adjusted: see chapter 6 .1 .3 .
4) Use the controls TREBLE and BASS (9) to
adjust the tone .
6.1 Module "MP3 player / Bluetooth
receiver / FM radio"
When the SA-130DMP is switched on, the mod-
ule "MP3 player / Bluetooth receiver / FM radio"
will automatically be activated .
The infrared remote control is operated with
a 3 V button cell (type CR 2025) . If a battery is
already inserted in the remote control, remove
the insulating film (to protect the battery from
being discharged) from the battery holder .
After that, the remote control is ready for op-
eration . When pressing a button, always point
the remote control to the infrared sensor (15) .
Make sure that there are no obstacles between
the remote control and the sensor .
If the remote control is not used for a
longer period of time, remove the battery as a
precaution so that the remote control will not
be damaged in case the battery should leak .
4
12
very high volume . Permanent
high volumes may damage your
hearing!
5 6 7 8
Inserting / Replacing the battery:
1) Push the latch of the battery holder to the
right (first arrow in figure 4) and pull out
the holder (second arrow) .
➃
1.
2) To replace a battery, remove the discharged
battery .
3) Insert a new battery in the holder, positive
pole facing upwards . Push the holder back
into the remote control .
Never put batteries in the house-
hold waste . Always dispose of the
batteries in accordance with local
regulations .
6.1.1 Switching the module off /on
To switch the module off and to switch it on
again, use the button
control .

6.1.2 Selecting the operating mode

Use the button MODE (21) to switch over be-
tween the operating modes:
USB medium Memory card
6.1.3 Adjusting the basic volume
To adjust the basic volume (adjustment range
to ), use the buttons
00 32
the remote control or keep the button
or (24) at the device pressed .
I

6.1.4 Muting
To mute the sound, press the button
the remote control;
display (16) . To unmute the sound, press the
button again .
6.1.5 Operating mode "USB medium"
or "Memory card"
The player can be used to reproduce MP3
files from memory cards (SD / SDHC / SDXC)
and USB storage media (USB flash drive or
USB hard disk with separate power supply) .
The reproduction of WMA files and WAV files
is also supported .
Note: Due to the large number of storage device
manufacturers and device drivers, it cannot be guar-
anteed that all storage media are compatible with
the player .
9
13 14
2.
(26) on the remote
Bluetooth Radio
and (28) on
I

(27) on
will appear on the
MUTE