Feature Description; Intended Use; Limitations On Use; Instructions For Use - Dräger X-plore 8000 Gebrauchsanweisung

en |
Description
4 Visor bracket
5 Press studs
6 Visor
7 Face cuff
A protective foil is available as an accessory. The protective foil is fitted to the
visor with the press studs and protects it against scratches, paint particles and
dust.
In addition, earmuffs can be mounted on the helmet as an option. For
information on noise dampening, see chapter 9 Technical data.
3.2

Feature description

®
The Dräger X-plore 8000 helmet with visor consists of a safety helmet with a
visor and face cuff.
The safety helmet absorbs the energy of an impact through the partial
destruction or damaging of the helmet's shell. The visor protects the face
against solid and liquid particles. The face cuff fits the contours of the face. The
resulting overpressure prevents polluted ambient air from penetrating. Excess
air escapes through ventilation holes in the face cuff. A ventilation duct is
integrated in the safety helmet.
If a powered air purifying respirator or air line breathing apparatus is connected,
the filtered air is guided in front of the user's face through the ventilation duct.
3.3

Intended use

®
The Dräger X-plore 8000 helmet with visor is dedicated for use with the Dräger
®
X-plore 7300/7500 and Dräger X-plore
®
or the Dräger X-plore 9000 air line breathing apparatus. In the USA the Dräger
®
X-plore 8000 helmet with visor is only permitted to be used with Dräger X-
®
plore 8000 powered air purifying respirators.
®
The Dräger X-plore 8000 helmet with visor is also suitable for users wearing
glasses and beards.
®
1) X-plore is a registered trademark of Dräger.
14
11 Sweatband
12 Support ring
13 Tube connection
®
8000 powered air purifying respirators
3.4

Limitations on use

To make sure that enough clean air is available, the Dräger X-plore
helmet with visor must only be used in conjunction with the devices specified in
chapter 3.3 Intended use.
The protective effect can be impaired by the following factors:
– High wind velocities and strong crosswind
– Earpieces or beards under the face cuff
3.5 Approvals
For information on the corresponding system approvals please refer to the
instructions for use of the respirators mentioned in 3.3 Intended use.
The Dräger X-plore® 8000 helmet with visor fulfils the following regulations:
– (EU) 2016/425
– (EU) 2016/425 as brought into UK law and amended
Declarations of conformity: see www.draeger.com/product-certificates
The safety helmet is approved in accordance with the following standards:
– EN 397:2012+A1:2012
– EN 50365:2002
– ANSI ISEA Z89.1-2009
The visor is approved in accordance with the following standards:
1)
– EN 166:2001
– ANSI ISEA Z87.1-2010
The earmuffs are approved in accordance with the following standards:
– EN 352-3:2002
– ANSI S3.19-1974
In the USA the Dräger X-plore
combination with the Dräger X-plore
accordance with Part 84, Title 42 of the Code of Federal Regulations. It is only
permitted to be used together with components that have NIOSH approval (see
Approval Label of the Dräger X-plore

Instructions for use

|
Dräger X-plore 8000
®
8000 helmet with visor is approved in
®
8000 powered air purifying respirator in
®
8000 blower unit).
®
Helmet with Visor
®
8000