Connecting To The Mains; Electrical Safety - Bosch UniversalRotak 650 Originalbetriebsanleitung

− Exercise extreme caution when changing direction on
slopes.
Use extreme caution when stepping back or pulling the
u
machine towards you.
Never mow by pulling the mower towards you.
u
Wait until the blades stop if the machine has to be tilted
u
for transportation when crossing surfaces other than
grass and when transporting the machine to and from the
area to be mowed.
Do not tilt the machine when starting or switching on the
u
motor.
Switch on the motor according to the instructions with
u
feet well away from rotating parts.
Do not put hands or feet near or under rotating parts.
u
Always stand clear of the discharge zone when operating
u
the machine.
Never pick up or carry the machine while the motor is run-
u
ning.
When storing, make sure that all 4 wheels of the garden
u
tool stand on the ground/floor.
Only lift the garden tool with the carrying handle. Use the
u
carrying handle with care.
Do not modify the machine. Unauthorized modifications
u
can impair the safety of your machine, lead to increased
noise and vibrations, and poor performance.
Regularly inspect the supply cable and any extension
u
cables. Do not connect damaged cables to the supply or
touch a damaged cable before it is disconnected from the
supply. A damaged cable can lead to contact with live
parts. Beware electric shock hazard.
Leaf Collect
The leaf collect blade has been designed to allow you to pick
up autumn leaves from your lawn. In order for this function-
ality to work within optimal parameters, please note the fol-
lowing:
– Only collect leaves with the machine set at maximum cut-
ting height.
– Collect leaves from your lawn only.
– Before collecting leaves inspect the area where the ma-
chine is to be used and keep people, pets, glass struc-
tures and cars away from use.
Remove the plug from the socket:
– Whenever you leave the machine.
– Before clearing a blockage.
– Before checking, cleaning or working on the machine.
– After striking a foreign object. Inspect the machine for
damage and change the blade as necessary.
– If the machine starts to vibrate abnormally (check imme-
diately).
Bosch Power Tools

Connecting to the mains

The voltage indicated on the rating plate must correspond
u
to the voltage of the power source.
Only use this product when connected into a socket
u
which is protected by a circuit-breaker that would be ac-
tuated by a 30 mA residual current.
Only use or replace power supply cables for this unit
u
which correspond to the types indicated by the manufac-
turer. See the operating instructions for the order no. and
types.
Never touch the mains plug with wet hands.
u
Do not run over, crush or pull the power supply cord or
u
extension cord, otherwise it may be damaged. Protect the
cable from heat, oil and sharp edges.
The extension lead must have a cross section in accord-
u
ance with the operating instructions and be protected
against splashed water. The connection must not be in
water.
Always wear gardening gloves when handling or work-
u
ing near the sharp blade/tines.

Electrical Safety

Warning! Switch the product off and pull the
mains plug before any maintenance or
cleaning. The same applies when the mains
cable is damaged, cut or entangled.
The blade/tines continues to rotate for a few seconds
u
after the machine is switched off.
Caution do not touch the rotating blade/tines.
u
Your product is double insulated for safety and requires no
earth connection. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applicable). Contact
your Bosch Service Centre for details. If in doubt contact a
qualified electrician or the nearest Bosch Service Centre.
For electrical safety use a Residual Current Device (RCD)
u
with a tripping current of not more than 30 mA. Always
check your RCD every time you use it.
Keep the supply cables away from moving hazardous parts
and avoid damage to the cables; this can lead to contact with
live parts.
The connections (plugs and sockets) should be kept dry and
off the ground.
The supply cables must be inspected for signs of damage at
regular intervals and may only be used if in perfect condi-
tion.
If the supply cable on the product is damaged, it must only
be replaced by a Bosch Service Centre. Only use approved
extension cables.
Use only extension cords, cables, leads and cable reels that
comply with EN 61242/IEC 61242 or IEC 60884-2-7 and
are of type H05VV-F or H05RN-F.
If you want to use an extension cable when operating your
product, only the following cable dimensions should be
used:
English | 9
F 016 L94 646 | (01.03.2023)