Makita DUR361U Betriebsanleitung Seite 16

Nylon cutting head (optional accessory
for a product that comes with a cutter
blade)
Nylon cutting head
NOTICE:
• Do not attempt to bump feed the head while the tool is
operating at a high RPM. Bump feeding at a high RPM
may cause damage to the nylon cutting head.
• The bump feed will not operate properly if the head is
not rotating. (Fig. 14)
The nylon cutting head is a dual string trimmer head
provided with a bump & feed mechanism.
To cause the nylon cord to feed out, the cutting head
should be bumped against the ground while rotating at a
low RPM.
NOTE:
If the nylon cord does not feed out while bumping the
head, rewind/replace the nylon cord by following the
procedures described under "Maintenance."
ASSEMBLY
WARNING:
• Always be sure that the tool is switched off and
battery cartridge is removed before carrying out
any work on the tool. Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
• Never start the tool unless it is completely
assembled. Operation of the tool in a partially
assembled state may result in serious personal injury
from accidental start-up.
Installing the handle
For model DUR361U (Fig. 15)
Insert the shaft of the handle into the grip as shown. Align
the screw hole in the grip with the one in the shaft. Tighten
the screw securely.
Fit the barrier and grip onto the shaft pipe with four
screws. Make sure that the spacer on the shaft pipe is
located between the grip/barrier assembly and the
hanger.
Place handle between handle clamp and handle holder.
Adjust the handle to an angle that provides a comfortable
working position and then secure by firmly hand-
tightening knob. (Fig. 16)
For model DUR362L (Fig. 17)
Fit the grip onto the shaft pipe and tighten it with two hex
bolts. Make sure that the spacer on the shaft pipe is
located between the grip assembly and the other grip. Do
not remove or shrink the spacer.
Installing the guard
WARNING:
• Never use the tool without the guard illustrated in
place. Failure to do so can cause serious personal
injury.
For cutter blade (only for model DUR361U) (Fig. 18)
Install the protrusion of the protector clamp to the gear
case until aligning the position with the label on the pipe.
16
Fix the protector to the protector clamp with the two bolts
and then tighten both bolts by the hex wrench evenly.
(Fig. 19)
For nylon cutting head
For DUR362L (Fig. 20)
Align the protrusions on the protector attachment with the
grooves of the protector.
Align the protrusions on the protector holder attachment
with the groove of the protector holder. (Fig. 21)
After attaching the protector and the protector holder,
tighten the hex bolts securely. (Fig. 22)
For DUR361U (optional accessory)
Remove the hex bolts with hex wrench. Then remove the
protector clamp and protector. (Fig. 23)
Install the protector attachment and protector holder
attachment to the gear case.
To install the protector for nylon cutting head, follow the
installing method mentioned previously. (Fig. 24)
Installing the wire guard
CAUTION:
• Before adjusting the wire guard, wait for the cutting
head comes to standstill. Do not adjust the wire guard
with your foot.
To reduce the risk damaging the objects in front of the
cutting head, insert the wire guard so that it controls the
cutting range of the mowing line. (Fig. 25)
Slightly expand the wire guard outward and then insert it
into the holes of the protector. (Fig. 26)
NOTE:
• Do not expand the wire guard outward too much.
Otherwise it may break.
When wire guard is not in use, lift it for the idle position.
(Fig. 27)
Installing nylon cutting head
CAUTION:
• If during operation the nylon cutting head
accidentally impacts a rock or hard object the
trimmer should be stopped and inspected for any
damage. If the nylon cutting head is damaged it
should be replaced immediately. Use of a damaged
nylon cutting head could result in serious personal
injury.
NOTICE:
• Be sure to use genuine Makita nylon cutting head.
Turn the tool upside down so that you can replace the
nylon cutting head easily.
Insert the hex wrench through the hole on the protector
cover and rotate the receive washer until it is locked with
the hex wrench. The nylon cutting head onto the threaded
spindle directly and tighten it by turning it
counterclockwise. Remove the hex wrench.
To remove the nylon cutting head, turn the nylon cutting
head clockwise while holding the receive washer with the
hex wrench. (Fig. 28)