Storage; Cleaning And Care; Troubleshooting - Kärcher K 2 Battery Bedienungsanleitung

CAUTION
Risk of personal injury or damage!
Consider the weight of the appliance when storing it.
Storing the Appliance
 Park the machine on an even surface.
 Detach spray lance from the trigger gun.
 Engage the spray lance in its holder.
 Push the disconnect button on the trigger gun and
pull the high-pressure hose out of the trigger gun.
 Place the trigger gun into the storage for the trigger
gun.
 Push the casing of the quick coupling for the high
pressure hose toward the rear and disconnect the
high pressure hose from the appliance.
 Store the high-pressure hose on the device.
Prior to extended storage periods, as during the winter,
also observe the instructions in the Care section.
Frost protection
ATTENTION
Appliances and accessories that are not completely
drained can be destroyed by frost. Completely drain ap-
pliance and accessories and protect them against frost.
To avoid damage:
 Completely drain all water from the appliance:
Switch the appliance on with detached high pres-
sure hose and detached water supply (max. 1 min-
ute) and wait, until no more water exits at the high
pressure connection. Turn off the appliance.
 Store the appliance and the entire accessories in a
frost free room.
Battery pack
ATTENTION
Risk of damage! Store the battery packs in rooms with
low humidity and below 20 °C only.
This appliance must only be stored in interior rooms.
The battery pack indicates its current charging state on
the display, even without being connected to a charger.
If the battery pack display goes out during storage, the
battery capacity is fully depleted and the display has
been switched off. Please recharge the battery as soon
as possible.

Cleaning and care

DANGER
Short circuit hazard!
Do not clean the device with a hose or high-pressure
water jet.
Switch the device off and remove the battery pack be-
fore working on the device.
ATTENTION
Risk of damage!
Do not use any abrasive or aggressive detergents for
cleaning purposes.
Clean the sieve in the water connection
Clean the sieve in the water connection regularly.
ATTENTION
The sieve must not be damaged.
 Remove coupling from the water connection.
Illustration
 Pull the sieve out using flat pliers.
 Clean the sieve under running water.
 Reinsert the sieve into the water connection.
24

Storage

 Regularly check the battery terminals and adapter
for soiling and clean them as necessary.
 Recharge battery packs that are stored over a long-
er period of time.

Troubleshooting

DANGER
Repair work and work on the electrical components may
only be performed by an authorised customer service.
You can rectify minor faults yourself with the help of the
following overview.
If in doubt, please consult the authorized customer ser-
vice.
Appliance is not running
 Push the lever of the trigger gun, the device will
switch on.
 The battery pack is not seated correctly in the bat-
tery holder, insert the battery pack into the battery
holder and let it click into place.
 Let the battery pack cool down when overheated.
 Charging state of the battery pack (see display) too
low, charge the battery if necessary.
 Defect battery pack or charger, replace battery
pack or charger with new accessory.
The device switches off automatically
– After 2 minutes of dry running.
– When the battery pack is at risk of overheating.
Restarting:
 Let the battery pack cool down if necessary.
 Turn off the appliance "0/OFF".
 Turn on the appliance "I/ON".
Pressure does not build up in the appliance
 Appliance ventilation: Switch the appliance on with
the high-pressure hose detached and operate
(max. 2 minutes) until the water exits the high-pres-
sure connection without bubbles. Switch off appli-
ance and reconnect high-pressure hose.
 Check the water supply.
 Pull out the sieve in the water connection using flat-
nose pliers and clean under running water.
Strong pressure fluctuations
 Clean high-pressure nozzle: Remove dirt and de-
bris from the nozzle bore, using a needle and rinse
through with water from the front.
 Check water flow quantity.
No detergent infeed
 Detach spray lance from the trigger gun. Work only
with the trigger gun.
 Clean the detergent suction hose filter.
 Check the detergent suction hose for kinks.
Appliance is leaking
 Dropwise leakage of the device is normal for tech-
nical reasons. If the leakage increases contact the
authorized customer service.
– 13
EN
Care