Christopeit Sport 15072 Montage- Und Bedienungsanleitung Seite 26

Max Heart Rate in Program 18, and 95% Max Heart Rate in Program 19.
After pressing „START/STOP" key to exercise, please also apply the heart
rate detector appropriately. In these programs, the computer will adjust the
level of loading according to the heart rate detected. For example, the level
of loading may increase while the heart rate detected is lower than TARGET
H.R. Also, the level of loading may decrease while the heart rate detected is
higher than TARGET H.R. As a result, the user's heart rate will be adjusted to
close the TARGET H.R. in the range of TARGET H.R. –5 and TARGET H.R.
+5. With the input of age, the computer may suggest a target heart rate to
exercise. The suggested heart rate is 80% (220 – age).
So, if the heart rate detected equals to or greater than the TARGET H.R.,
the value of HEART RATE will keep flashing. Please note that it is a warning
for users to slow down or to lower the level of loading.
In program 20, press „F" key to select TIME, DISTANCE, CAL. and TARGET
H.R. Users may setup a target heart rate to exercise in a period of time or
a certain distance.
Training area in mm
(for home trainer and user)
Cleaning, Checks and Storage of the Ergometer
bike:
1. Cleaning
Use only a less wet cloth for cleaning. Caution: Never use benzene,
thinner or other aggressive cleaning agents for surface cleaning as
this damage caused.
The device is only for private home use and for use suitable indoors.
Keep the unit clean and moisture from the device.
2. Storage
Plug out the power supply unit while intending the unit for more than
4 weeks not to use. Push the saddle slide toward the handlebar and
the seat support tube as deeply as possible into the frame. Choose
a dry storage in-house and put some spray oil to the pedal bearings
left and right, to the thread of the handlebar bolt, and on the thread
of the quick release for saddle support.
Cover the bike to protect it from being discolor by any sunlight and
dirty through dust.
3. Checks
We recommend every 50 hours to review the screw connections for
tightness, which were prepared in the assembly. Every 100 operating
hours, you should put some spray oil at the pedal bearings left and
right, to the thread of the handlebar bolt and to the thread of quick
release for saddle support.
TEST-Pulse Recovery:
It is a function to check the condition of pulse recovery that is scaled from 1.0
to 6.0 while 1.0 means the best and 6.0 means the worst and the increment
is 0.1. In order to get rated correctly, users must test it right after the workout
finished by pressing „TEST" key and then stop exercising. After the key is
pressed, please also apply the heart rate detector appropriately. The test
will last for 1 minute and the result will show in the display.
Free area in mm
(Training area and security area
(rotating 60cm))
Troubleshooting
If you cannot solve the problem with the following information,
please contact the authorized service center.
Problem Possible Cause
Computer has No power
no value at Dis- adapter is well
play if you press plugged or wall
any key. power is without
power.
Computer is Sensor impulse
not counting missing base on
data and do not not well plugged
switch on after connection
start cycling.
Computer is Sensor impulse
not counting missing base on
data and do not not correct posi-
switch on after tion of sensor.
start cycling.
No pulse value Pulse cable is
not plugged in.
No pulse value Pulse sensors
not well connec-
ted
26
Solution
Check that the power adapter
is properly plugged in, possibly
with another electric device
check if the wall power is fine.
Check the plug connections at
computer and inside of handle-
bar support.
Take off the cover and check
the distance between magnet
and Sensor. The magnet at
turning belt wheel should have
only less than < 5mm distance
against the sensor position.
Check the separately pulse
cable is well connected with
computer.
Screw out the screw for pulse
measurement and check if
plugs are well connected and no
damage at pulse cable.