Before Starting The Equipment - EINHELL 44.125.50 Originalbetriebsanleitung

Anleitung_BT_BG_150_SPK1:_
Load factor:
A load factor of S2 30 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (150 W) for no longer than
the time stipulated on the specifications label (30
minutes ON period). If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Noise emission values
The noise emission values were measured in
accordance with EN 61029.
L sound pressure level 77,5 dB(A)
pA
K uncertainty
pA
L sound power level 90,5 dB(A)
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.

5. Before starting the equipment

Pull the power plug before doing any
maintenance or assembly work on the
equipment.
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench or similar.
26.05.2011 9:50 Uhr
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the grinding wheel to run
freely.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
5.1 Fitting the spark reflector (Fig. 3-4 / Item 3)
Fit the spark reflector (3) to the double wheel
grinder/sander using the adjusting screw (10).
5.2 Adjusting the spark reflector (Fig. 4-6 / Item
3)
Adjust the spark deflector (3) using the adjusting
screw (10) so that the distance between the dry
3 dB
grinding wheel (5) and the spark deflector (3) is
as small as possible and certainly does not
3 dB exceed 2 mm.
Adjust the spark deflector (3) periodically to
compensate for wear on the wheel.
5.3 Fitting the workpiece supports (Fig. 7-8 / Item
7)
Undo the fastening screws (6). Secure the
workpiece supports (7) to the double wheel
grinder/sander using the fastening screws (6).
5.4 Adjusting the workpiece supports (Fig. 8-9 /
Item 7)
Adjust the workpiece supports (7) using the
fastening screws (6) so that the distance between
the dry grinding wheel (5) and the workpiece
support (7) is as small as possible and certainly
does not exceed 2 mm.
Adjust the workpiece supports (7) periodically to
compensate for wear on the dry grinding wheel.
5.5 Changing the grinding wheel (Figs. 10-11)
Remove the 3 screws (A) holding the side section of
the safety hood (B) and remove the safety hood.
Undo the nut (D) (Important: The left grinding
wheel is fastened with a left-handed thread and
the right grinding wheel with a right-handed
thread), by holding the nut of the grinding wheel
mount on the opposite side. Remove the flange (C).
and replace the grinding wheel (5). To assemble,
proceed in reverse order.
Seite 11
GB
11