Makita DJR181 Bedienungsanleitung Seite 6

Adjusting the shoe
Fig.3
Fig.4
When the blade loses its cutting efficiency in one place
along its cutting edge, reposition the shoe to utilize a
sharp, unused portion of its cutting edge. This will help to
lengthen the life of the blade. To reposition the shoe,
push the shoe button in the "A" direction with a click and
reposition as shown in the figure which allows you to
make five-way adjustment. To secure the shoe, push the
shoe button in the "B" direction with a click.
Switch action
Fig.5
CAUTION:
Before inserting the battery cartridge into the tool, always
•
check to see that the switch trigger actuates properly and
returns to the "OFF" position when released.
When not operating the tool, depress the lock-off
•
button from A side to lock the switch trigger in the
OFF position.
To prevent the switch trigger from accidentally pulled,
the lock-off button is provided.
To start the tool, depress the lock-off button from B side
and pull the switch trigger.
Tool speed is increased by increasing pressure on the
switch trigger. Release the switch trigger to stop. After
use, always press in the lock-off button from A side.
Lighting up the front lamp (For DJR181)
Fig.6
CAUTION:
Do not look in the light or see the source of light
•
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 - 15 seconds after
the switch trigger is released.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp.
•
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
Hook (For DJR181)
Fig.7
CAUTION:
Depress the lock-off button from A side to lock the
•
switch trigger in the OFF position. (See the section
titled " switch action " .)
Never hook the tool at high location or on
•
potentially unstable surface.
The hook is convenient for hanging the tool temporarily.
To use the hook, simply lift up hook until it snaps into the
open position.
When not in use, always lower hook until it snaps into
the closed position.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing the saw blade
CAUTION:
Always clean out all chips or foreign matter
•
adhering to the blade, blade clamp and/or slider.
Failure to do so may cause insufficient tightening
of the blade, resulting in a serious injury.
To install the saw blade, always make sure that the
blade clamp lever is in released position
insulation cover before inserting the saw blade. If the
blade clamp lever is in fixed position, rotate the blade
clamp lever in the direction of the arrow so that it can be
locked at the released positon .
Fig.8
Insert the saw blade into the blade clamp as far as it will
go. The blade clamp lever rotates and the saw blade is
fixed. Make sure that the saw blade cannot be extracted
even though you try to pull it out.
Fig.9
NOTE:
If you do not insert the saw blade deep enough, the
•
saw blade may be ejected unexpectedly during
operation. This can be extremely dangerous.
If the lever is positioned inside the tool, switch on the
tool just a second to let the blade out as shown in the
figure.
Remove the battery cartridge from the tool.
To remove the saw blade, rotate the blade clamp lever in
the direction of the arrow fully. The saw blade is
removed and the blade clamp lever is fixed at the
released position .
Fig.10
NOTE:
Keep hands and fingers away from the lever during
•
the switching operation. Failure to do so may
cause personal injuries.
If you remove the saw blade without rotating the
•
blade clamp lever fully, the lever may not be locked
in the released position . In this case, rotate the
blade clamp lever fully again, then make sure that
the blade clamp lever locked at the released
position .
6
on the