Makita DF033D Betriebsanleitung Seite 9

Adjusting the fastening torque
► Fig.7: 1. Adjusting ring 2. Graduation 3. Arrow
The fastening torque can be adjusted in 21 levels by turning the adjusting ring. Align the graduations with the arrow
on the tool body. You can get the minimum fastening torque at 1 and maximum torque at
The clutch will slip at various torque levels when set at the number 1 to 20. The clutch does not work at
the marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
The following shows the rough guide of the relationship between the screw size and graduation.
Graduation
Machine screw
Wood Soft wood
screw (e.g. pine)
Hard wood
(e.g. lauan)
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/drill bit
For Model DF333D (optional accessory)
► Fig.8: 1. Sleeve 2. Close 3. Open
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
Installing or removing driver bit/socket bit
For Model DF033D (optional accessory)
► Fig.9
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
socket bit.
NOTE: Both shallower type (A=12 mm, B=9 mm) and
deeper type (A=17 mm, B=14 mm) of driver bits can
be used.
To install the driver bit, pull the sleeve in the direction of
the arrow and insert the driver bit into the sleeve as far
as it will go.
Then release the sleeve to secure the driver bit.
► Fig.10: 1. Driver bit 2. Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case, try re-inserting the bit according to the instruc-
tions above.
NOTE: After inserting the driver bit, make sure that it
is firmly secured. If it comes out, do not use it.
1 2 3 4 5 6
M4
–
–
7 8 9 10 11 12
M5
–
Installing hook
WARNING:
for their intended purposes only, e.g., hanging the
tool on a tool belt between jobs or work intervals.
WARNING:
hook as too much force or irregular overburden
may cause damages to the tool resulting in per-
sonal injury.
CAUTION:
secure it with the screw firmly. If not, the hook
may come off from the tool and result in the personal
injury.
CAUTION:
securely before releasing your hold. Insufficient
or unbalanced hooking may cause falling off and you
may be injured.
► Fig.11: 1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
Using hole
WARNING:
unintended purpose, for instance, tethering the
tool at high location. Bearing stress in a heavily
loaded hole may cause damages to the hole, result-
ing in injuries to you or people around or below you.
► Fig.12: 1. Hanging hole
Use the hanging hole at the bottom rear of the tool to
hang the tool on a wall using a hanging cord or similar
strings.
9 ENGLISH
marking.
13 14 15 16 17
ø3.5 x 22 ø4.1 x 38
ø3.5 x 22
Use the hanging/mounting parts
Be careful not to overload the
When installing the hook, always
Make sure to hang the tool
Never use the hanging hole for
18 19 20
M6
–
ø4.1 x 38