Do not attempt to service this product yourself. Refer all servicing to authorized service centers, 2016 and all other applicable UK regulations. The complete declaration of installers, technicians, dealers or distributors. To contact Bose Professional or to find a dealer or conformity can be found at: www.Bose.com/compliance distributor near you, visit PRO.BOSE.COM.
0.22 in 8.27 in 267 mm 10.50 in Technical Specifications Important Installation Information For additional specifications, see the DesignMax DM6SE technical Before installing the loudspeaker, review Important Safety data sheet at PRO.BOSE.COM. Instructions on page 2. Physical Product Dimensions Height: 340 mm (13.39 in) Width: 222 mm (8.74 in)
Euroblock connector. Note: If using the wide open rubber conduit configuration, it is the installer's responsibility to seal against water ingress into the Euroblock connector. 4 • English DesignMax DM6SE • Installation Guide...
Setup PRO.BOSE.COM Wiring the Loudspeaker Wire Gauge The DesignMax DM6SE loudspeaker is designed to work with 18 AWG (0.8 mm ) to 14 AWG (2.1 mm ) size wire only. Connection Diagrams Expose six millimeters (1/4 inch) of bare wire to attach to the terminals.
For outdoor installations, insert the wires through the bottom of the input cover. See Preparing the Weather- resistant Input Cover on page 4. Wire the connector. For wiring information, see Wiring the Loudspeaker on page 5. 6 • English DesignMax DM6SE • Installation Guide...
Seite 7
For outdoor installations, place the weather-resistant input cover over the connector and press it firmly against the loudspeaker to create a tight seal. See Preparing the Weather- resistant Input Cover on page 4. Installation Guide • DesignMax DM6SE English • 7...
Suitable for installation using Class 1, Class 2, Class 3 wiring methods in accordance with NFPA 70, National Electrical Code, 2017, Article 640 The DesignMax DM6SE loudspeaker has been designed to the requirements defined in the following European regulatory specification for combination systems: Tested to IEC60268-5, 2007 8 •...
• Utilice solo el hardware y los accesorios incluidos, o bien los que Bose especifica como aptos para los altavoces DesignMax DM6SE. No se suministran los componentes para fijar el altavoz a la superficie de montaje. Para obtener información sobre los accesorios compatibles, consulte la hoja de datos técnicos del producto en PRO.BOSE.COM.
Alto: 340 mm (13.39") Ancho: 222 mm (8.74") Profundidad: 229 mm (9.00") Peso neto, altavoz con rejilla 6.40 kg (14.1 lb) y soporte (individual) Peso de envío (par) 14.74 kg (32.5 lb) 10 • Español Guía de instalación de • DesignMax DM6SE...
Euroblock. Nota: Si utiliza el formato del conducto de goma de abertura completa, es responsabilidad del instalador sellarlo para que no entre agua en el conector Euroblock. Guía de instalación de • DesignMax DM6SE Español • 11...
Seite 12
PRO.BOSE.COM Cableado de los altavoces Calibre de cable El altavoz DesignMax DM6SE está diseñado para funcionar únicamente con cables que midan de 18 AWG (0.8 mm ) a 14 AWG (2.1 mm Diagramas de conexión Exponga 6 milímetros (1/4") de cable sin aislación para conectarlo a los terminales.
Consulte Preparación de la cubierta de entrada resistente a la intemperie en la página 11. Conecte el altavoz. Para obtener información sobre el cableado, consulte Conexión del altavoz en la página 12. Guía de instalación de • DesignMax DM6SE Español • 13...
Apto para la instalación con métodos de cableado Clase 1, Clase 2 y Clase 3 de conformidad con el estándar NFPA 70, Código Eléctrico Nacional, 2017, Artículo 640 El altavoz DesignMax DM6SE se diseñó según los requisitos definidos en la siguiente especificación reglamentaria europea para sistemas combinados: Probado según IEC60268-5, 2007...
L’attestation complète de conformité est disponible à à des centres de service, installateurs, techniciens, revendeurs ou distributeurs agréés. Pour contacter Bose Professional ou pour trouver un revendeur ou un distributeur près de chez vous, l’adresse www.Bose.com/compliance rendez-vous à l’adresse PRO.BOSE.COM.
Caractéristiques techniques Informations importantes concernant l’installation Vous trouverez des caractéristiques supplémentaires dans la fiche technique du produit DesignMax DM6SE sur PRO.BOSE.COM. Avant d’installer l’enceinte, veuillez consulter les Consignes de sécurité importantes sur la page 16. Caractéristiques physiques Dimensions du produit Hauteur : 340 mm (13,39 po)
Seite 18
Euroblock contre la pénétration d’eau. Remarque : en cas d’utilisation d’un conduit en caoutchouc largement ouvert, il est de la responsabilité de l’installateur d’assurer l’étanchéité du connecteur Euroblock contre la pénétration d’eau. 18 • Français DesignMax DM6SE • Guide d’installation...
Seite 19
Installation PRO.BOSE.COM Câblage de l’enceinte Épaisseur des câbles L’enceinte DesignMax DM6SE est conçue pour fonctionner avec des câbles de taille 18 (0,8 mm ) à 14 AWG (2,1 mm ) uniquement. Diagrammes de connexion Exposez six millimètres (1/4 po) de fil dénudé à relier aux bornes.
Consultez la section Préparation du capot de protection des entrées résistant aux intempéries en page 18. Câblez le connecteur. Consultez la section Câblage de l’enceinte à la page 19 pour plus d’informations sur le câblage. 20 • Français DesignMax DM6SE • Guide d’installation...
étanchéité parfaite. Consultez la section Préparation du capot de protection des entrées résistant aux intempéries en page 18. Guide d’installation • DesignMax DM6SE Français • 21...
Seite 22
Conformité aux réglementations et aux normes de sécurité en vigueur L’enceinte Bose DesignMax DM6SE a été soumise avec succès à une phase complète de tests et elle est conforme aux spécifications et utilisations suivantes : Conformes à la norme ANSI/UL 1480A-2016, Enceintes destinées à un usage professionnel (sécurité) et commercial Utilisation générale, catégorie UL UEAY, dossier S 5591, numéro de contrôle 3N89...
Kerzen oder ähnliches auf das Gerät oder in die Nähe des Geräts. • Nehmen Sie keine nicht genehmigten Änderungen an diesem Produkt vor. • Die DesignMax DM6SE Wandhalterung ist ausschließlich für die Verwendung mit dem Lautsprechermodell DM6SE geeignet. • Stellen Sie sicher, dass der Lautsprecher und die Montagekomponenten nicht mit chemischen Substanzen in Berührung kommen, die nicht von Bose zugelassen sind.
Technische Spezifikationen Wichtige Installationshinweise Bitte lesen Sie vor der Installation des Lautsprechers den Weitere technische Spezifikationen können Sie dem technischen Abschnitt Wichtige Sicherheitshinweise auf Seite 23. Datenblatt für den DesignMax DM6SE auf PRO.BOSE.COM entnehmen. Material, Abmessungen, Gewicht Produktabmessungen Höhe: 340 mm Breite: 222 mm...
Euroblock-Anschluss vor eindringendem Wasser geschützt ist. Hinweis: Wird die große Öffnung der Gummiummantelung verwendet, ist der Monteur dafür verantwortlich, sie so abzudichten, dass der Euroblock-Anschluss vor eindringendem Wasser geschützt ist. Installationsanleitung • DesignMax DM6SE Deutsch • 25...
Systemeinrichtung PRO.BOSE.COM Verkabeln des Lautsprechers Kabeldurchmesser Der DesignMax DM6SE Lautsprecher wurde für den ausschließlichen Gebrauch mit Kabeln der Größen 18 AWG (0,8 mm ) bis 14 AWG (2,1 mm ) entwickelt. Anschlussdiagramme Isolieren Sie einen Teil des Drahtes (6 mm) für den Anschluss an die Anschlüsse ab.
Führen Sie bei Installationen im Freien die Kabel durch die Unterseite der Abdeckung der Anschlüsse. Siehe Vorbereitung der wetterbeständigen Abdeckung der Anschlüsse auf Seite 25. Verkabeln Sie den Anschluss. Weitere Informationen zur Verkabelung finden Sie unter Verkabeln des Lautsprechers auf Seite 26. Installationsanleitung • DesignMax DM6SE Deutsch • 27...
Wenn Sie den Lautsprecher im Außenbereich anbringen, positionieren Sie die wetterbeständige Abdeckung der Anschlüsse über den Anschlüssen und drücken Sie sie fest auf den Lautsprecher, um die Abdeckung abzudichten. Siehe Vorbereitung der wetterbeständigen Abdeckung der Anschlüsse auf Seite 25. 28 • Deutsch DesignMax DM6SE • Installationsanleitung...
Sie so die Befestigungslaschen. Nun können Sie die Frontabdeckung vom Lautsprecher entfernen. Sicherheitshinweise und gesetzliche Bestimmungen Der Bose DesignMax DM6SE Lautsprecher hat umfassende Testreihen bestanden und entspricht den folgenden Normen und Einsatzanforderungen: Zertifiziert gemäß ANSI/UL 1480A-2016, Speakers for Commercial & Professional Use Allgemeine Gebrauchsfähigkeit –...
Seite 30
(ad esempio, candele accese) sull’apparecchio o in prossimità di esso. • Non apportare alterazioni non autorizzate al prodotto. • La staffa per l’installazione a muro del DesignMax DM6SE può essere utilizzata solo con questo modello. • Evitare di esporre il diffusore o i suoi componenti di montaggio a sostanze chimiche non specificate da Bose, inclusi a titolo esemplificativo lubrificanti e detergenti, spray per contatti e altri solventi a base di idrocarburi.
Dimensioni del prodotto Altezza: 340 mm Larghezza: 222 mm Profondità: 229 mm Peso netto del diffusore con 6,40 kg (14,1 lb) griglia e staffa (singolo) Peso di spedizione (coppia) 14,74 kg (32,5 lb) Guida all’installazione • DesignMax DM6SE Italiano • 31...
Seite 32
è responsabilità dell’installatore sigillarlo per prevenire penetrazioni di acqua nel connettore Euroblock. Nota: se viene utilizzata la configurazione con tubo protettivo in gomma aperto, è responsabilità dell’installatore sigillarlo per prevenire penetrazioni di acqua nel connettore Euroblock. 32 • Italiano DesignMax DM6SE • Guida all’installazione...
PRO.BOSE.COM Cablaggio del diffusore Diametro dei cablaggi Il diffusore DesignMax DM6SE è concepito esclusivamente per l’impiego con cavi di dimensioni comprese tra 18 AWG (0,8 mm ) e 14 AWG (2,1 mm Schemi di collegamento Scoprire 6 mm di filo non rivestito da collegare ai terminali.
Seite 34
Vedere Preparazione della cover di protezione degli ingressi resistente agli agenti atmosferici a pagina 32. Cablare il connettore. Per informazioni sul cablaggio, vedere Cablaggio del diffusore a pag. 33. 34 • Italiano DesignMax DM6SE • Guida all’installazione...
Per le installazioni in esterni, posizionare la cover di protezione degli ingressi sul connettore e premerla con decisione contro il diffusore per assicurarne la tenuta. Vedere Preparazione della cover di protezione degli ingressi resistente agli agenti atmosferici a pagina 32. Guida all’installazione • DesignMax DM6SE Italiano • 35...
Conformità alle norme di sicurezza Il diffusore Bose DesignMax DM6SE ha superato i test ai quali è stato sottoposto, risultando conforme alle specifiche e alle applicazioni indicate di seguito: Conforme alle specifiche ANSI/UL 1480A-2016, Diffusori per uso professionale e commerciale e di sicurezza Utilizzo generico - UL Categoria UEAY, Numero file S 5591 Numero controllo 3N89 Il modello DesignMax DM6SE è...
Om contact op te nemen www.Bose.com/compliance met Bose Professional en voor informatie over de dichtstbijzijnde dealer of distributeur, gaat u naar Dit symbool betekent dat het product niet mag worden weggegooid als huishoudelijk PRO.BOSE.COM.
267 mm Technische specificaties Belangrijke installatie-informatie Raadpleeg voor aanvullende specificaties het datasheet Lees voordat u de luidspreker installeert Belangrijke met technische gegevens voor de DesignMax DM6SE op veiligheidsinstructies op pagina 37. PRO.BOSE.COM. Fysiek Afmetingen van het product Hoogte: 340 mm...
Euroblock- connector voorkomt. Opmerking: Bij de volledig open-configuratie is het de verantwoordelijkheid van de installateur om voor afdichting te zorgen die het binnendringen van water in de Euroblock-connector voorkomt. Installatiehandleiding • DesignMax DM6SE Nederlands • 39...
Seite 40
PRO.BOSE.COM De luidspreker bekabelen Bekabelingsdiameter De DesignMax DM6SE loudspeaker is uitsluitend ontworpen voor bedrading van 18 AWG (0,8 mm ) tot 14 AWG (2,1 mm Aansluitdiagrammen Strip zes millimeter van de kabelisolatie voor bevestiging van de kale kabel aan de aansluitingen.
Seite 41
Verwijder de connector uit de luidspreker. Haal bij montage buiten de kabels door de onderkant van de afdekking. Raadpleeg De weerbestendige afdekking voorbereiden op pagina 39. Bekabel de connector. Raadpleeg voor bekabelingsinformatie De luidspreker bekabelen op pagina Installatiehandleiding • DesignMax DM6SE Nederlands • 41...
Plaats voor montage buiten de weerbestendige afdekking over de connector en druk de afdekking stevig tegen de luidspreker voor een goede afdichting. Raadpleeg De weerbestendige afdekking voorbereiden op pagina 39. 42 • Nederlands DesignMax DM6SE • Installatiehandleiding...
Seite 43
Geschikt voor installatie middels bekabelingsmethoden Klasse 1, Klasse 2 en Klasse 3 volgens NFPA 70, National Electrical Code, 2017, artikel 640 De DesignMax DM6SE loudspeaker is ontworpen volgens de vereisten die zijn vastgelegd in onderstaande specificatie van Europese regelgeving voor combinatiesystemen: Getest volgens IEC60268-5, 2007 Installatiehandleiding •...
• Bruk bare utstyret og tilbehøret som følger med, eller som er spesifisert av Bose for bruk med DesignMax DM6SE-høyttalere. Jernvare for å feste høyttaleren til overflaten er ikke inkludert. Hvis du vil ha informasjon om kompatibelt tilbehør, kan du se produktets tekniske dataark på...
Tekniske spesifikasjoner Viktig informasjon om montering Hvis du vil ha flere spesifikasjoner, kan du se det tekniske dataarket Før du monterer høyttaleren, må du se gjennom Viktige for DesignMax DM6SE på PRO.BOSE.COM. sikkerhetsinstruksjoner på side 44. Fysisk Produktmål Høyde: 340 mm...
Seite 46
Merk: Hvis du installerer høyttaleren med gummirøret vendt oppover, er det montørens ansvar å forsegle mot vanninntrenging i Euroblock- kontakten. Merk: Hvis du bruke det åpne gummirøroppsettet, er det montørens ansvar å forsegle mot vanninntrenging i Euroblock-kontakten. 46 • Norsk DesignMax DM6SE • Monteringsveiledning...
Seite 47
Konfigurering PRO.BOSE.COM Kable høyttaleren Kabeldiameter DesignMax DM6SE-høyttaleren er utformet for å fungere kun med kabler på mellom 18 AWG (0,8 mm ) til 14 AWG (2,1 mm Koblingsdiagrammer Eksponer seks millimeter av ledningen for å feste til terminalene. Merk: Høyttaleren er ikke sertifisert for bruk med et stivt rør.
Seite 48
Se Klargjøre det værbestandige trekket til inngangen på side 46. Sett ledningene i kontakten. Hvis du vil ha mer informasjon om kabling, kan du se Kable høyttaleren på side 47. 48 • Norsk DesignMax DM6SE • Monteringsveiledning...
Seite 49
For utendørsmontering plasserer du det værbestandige trekket til inngangen over kontakten og trykker det godt mot høyttaleren for å skape en tett forsegling. Se Klargjøre det værbestandige trekket til inngangen på side 46. Monteringsveiledning • DesignMax DM6SE Norsk • 49...
Seite 50
Kan brukes til montering ved hjelp av kabelmetoder i klasse 1, klasse 2 eller klasse 3, i samsvar med NFPA 70, National Electrical Code, 2017, artikkel 640 DesignMax DM6SE-høyttaleren er utformet i henhold til kravene som er definert i følgende europeiske forskrifter for kombinasjonssystemer: Testet i samsvar med IEC60268-5, 2007 50 •...
źródeł otwartego ognia, np. zapalonych świec. • Nie wolno dokonywać modyfikacji produktu bez zezwolenia. • Wspornik do montażu ściennego DesignMax DM6SE jest przeznaczony wyłącznie do modelu DM6SE. • Nie wolno narażać głośnika lub elementów montażowych na działanie substancji chemicznych, które nie zostały dozwolone przez firmę...
10,50 cala Dane techniczne Ważne informacje dotyczące instalacji Dodatkowe dane techniczne można znaleźć w arkuszu danych Przed rozpoczęciem montażu głośnika zapoznaj się z technicznych DesignMax DM6SE na stronie PRO.BOSE.COM. Ważnymi zaleceniami dotyczącymi bezpieczeństwa znajdującymi się na stronie 51. Fizyczne Wymiary produktu Wysokość: 340 mm (13,39 cala)
Uwaga: instalując głośnik z gumową rurką skierowaną do góry, instalator musi zabezpieczyć system przed wniknięciem wody do złącza Euroblock. Uwaga: wybierając całkowicie otwartą konfigurację gumowej rurki, instalator musi zabezpieczyć system przed wniknięciem wody do złącza Euroblock. Podręcznik instalacji • DesignMax DM6SE Polski • 53...
Seite 54
Konfiguracja PRO.BOSE.COM Okablowanie głośnika Grubość przewodu Do montażu głośnika DesignMax DM6SE należy stosować wyłącznie przewody o rozmiarze od 18 AWG (0,8 mm ) do 14 AWG (2,1 mm Schematy połączeń Odsłonić sześć milimetrów (1/4 cala) nieizolowanego przewodu, aby podłączyć go do zacisków. Uwaga: głośnik nie jest przeznaczony do użytku ze...
Seite 55
53, w sekcji Przygotowanie osłony chroniącej przed działaniem warunków atmosferycznych. Podłączyć przewody do złącza. Informacje na temat okablowania można znaleźć w sekcji Podłączanie okablowania do głośnika na stronie 54. Podręcznik instalacji • DesignMax DM6SE Polski • 55...
Seite 56
Więcej informacji znajduje się na stronie 53, w sekcji Przygotowanie osłony chroniącej przed działaniem warunków atmosferycznych. 56 • Polski DesignMax DM6SE • Podręcznik instalacji...
Zgodność z normami ANSI/UL 1480A-2016, Głośniki do bezpiecznego użytku komercyjnego i specjalistycznego Do zastosowań ogólnych – kategoria UL UEAY, numer pliku S 5591, numer kontrolny 3N89 Głośnik DesignMax DM6SE nadaje się do użytku zewnętrznego w wilgotnym środowisku Głośniki nadają się do instalacji przy użyciu okablowania klasy 1, klasy 2 lub klasy 3 zgodnie z normą NFPA 70, National Electric Code, 2017, art.
Seite 73
340 mm Ø 5.5 mm 210 mm 267 mm 技術仕様 設置に関する重要な情報 詳細な仕様は、PRO.BOSE.COMに用意されている、DesignMax DM6SEの スピーカーを設置する前に、72ページの安全上の重要な注意事項を テクニカルデータシートを参照してください。 ご確認ください。 物理的仕様 高さ: 340 mm 製品寸法 幅: 222 mm 奥行き: 229 mm 6.40 kg 質量(グリルおよびブラケット装着時 のスピーカー、単体) 梱包質量(ペア) 約14.74 kg 設置ガイド • DesignMax DM6SE 日本語 • 73...
Seite 81
.Euroblock المحكم لمنع دخول الماء إلى داخل الموصل الطرفي من النوع األوروبي مالحظة: إذا كان يتم استخدام تكوين القناة المطاطية المفتوحة على مصراعيها، فإن فني التركيب يتحمل مسؤولية .Euroblock اإلغالق المحكم لمنع دخول الماء إلى داخل الموصل الطرفي من النوع األوروبي • دليل التركيبDesignMax DM6SE 18 • العربية...
Seite 82
.ولوائح البناء المحلية .يمكن تثبيت كبل أمان بمك ب ّر الصوت باستخدام وليجة ملولبة بالجزء الخلفي من العلبة .) (غير مرفق) بعمق ملليمتر ً ا (95.0 بوصةM8 يتسع حجم الوليجة لبرغي 8 • العربية DesignMax DM6SE • دليل التركيب...
Seite 83
.8 راجع تحضير غطاء اإلدخال المقاوم لظروف الطقس في صفحة اربط المو ص ّ ل سلك ي ًا. للحصول على معلومات حول توصيل األسالك، راجع توصيل .8 أسالك مكبر الصوت في الصفحة • دليل التركيبDesignMax DM6SE 38 • العربية...
Seite 84
4. بالنسبة لعمليات التركيب الخارجية، ضع غطاء الدخل المقاوم لظروف الطقس على الموصل واضغط عليه بإحكام مقابل مكبر الصوت إلقفاله بطريقة محكمة. راجع تحضير غطاء الدخل .81 المقاوم لظروف الطقس في الصفحة 8 • العربية DesignMax DM6SE • دليل التركيب...
Seite 85
: وف ق ً ا للمتطلبات المحددة في المواصفات التنظيمية األوروبية التالية لألنظمة المج م َّ عةDesignMax DM SE تم تصميم مكبر الصوت 00 ، لعامIEC60268-5 تم االختبار وف ق ً ا لمعيار • دليل التركيبDesignMax DM6SE 58 • العربية...