Inhaltsverzeichnis
Werbung
Anleitung HS 580 SPK 1
26.
Do not use the hedge trimmer with a damaged
or excessively worn cutting system.
27.
Never try to work with an incomplete machine
or a machine with unapproved modifications.
28.
Check your surroundings and take note of any
potential dangers which you may not be able
hear due to the machine's noise.
29.
It is advisable not to use the hedge trimmer
when other persons, and particularly children,
are nearby.
30.
Children are not allowed to use the hedge
trimmer.
31.
Noise at the workplace may exceed 85 dB(A).
In this case, the operator must wear ear-muffs
or similar. The noise level of this electric tool is
measured in accordance with IEC 59 CO 11;
IEC 704; DIN 45635-1, D.3.1; and NFS 31-031
(84/537 EWG).
32.
Vibrations on the handle were measured in
accordance with EN 50144-2-15.
33.
Please use an RCD with this unit.
2. Layout (see Fig. 1)
1. Cutter
2. Hand guard
3. Guide handle with switch button
4. Handle with switch buttons above and below
5. Cable holder
6. Power cable
7. Cutter guard
8. Impact guard
9. Trimmings collector
10. Fastening screws for trimmings collector
Important! You must never use the hedge trim-
mer without wearing gloves.
3. Explanation of the plate (see Fig. 3)
1. Warning
2. Keep out of the rain and protect from getting wet.
3. Read the operating instructions before using for
the first time.
4. Pull the plug from the power supply immediately
if the cable gets damaged or severed.
5. Wear goggles and ear muffs.
18.01.2005
15:23 Uhr
Seite 15
4. Technical data
Voltage
Power consumption
Cutting length
Cutter rail length
Tooth spacing
Cuts/min
Sound power level LWA
Sound pressure level LPA
Vibration aw
Weight
5. Voltage
The machine can only be run on single-phase alter-
nating current with 230V ~ 50Hz a.c. voltage. Before
you use the machine for the first time, check that the
mains voltage is the same as the operating voltage
shown on the machine rating plate.
6. Using for the first time and operation
Important! This hedge trimmer is designed for the
trimming of hedges, bushes and shrubs. If it is used
for any other purpose not expressly permitted by
these operating instructions there may be a risk of
damage to the hedge trimmer or serious injury to the
user. The hedge trimmer comes with a two-hand
safety switch. It only works if the switch on the guide
handle (Fig. 2 / Item 1) is pressed with one hand and
either the switch on top of the handle (Fig. 2 / Item 2)
or the switch below the handle (Fig. 2 / Item 3) is
pressed with the other hand.
Releasing any of the switches will bring the hedge
trimmer to a stop.
b
Rotatable rear handle (Fig. 2/4/5)
The hedge trimmer comes with a rotatable rear
handle. This can be turned towards the left by
90° and towards the right by both 90° and 180°.
To do so, the slide (see Fig. 2/Item 4; Fig. 4/Item
4; Fig. 5/Item 4) must be slid in the direction of
the arrow. If turned to the left the handle locks
into position at 90° (Fig. 4). If turned to the right
the handle locks at 90° or 180° (Fig. 5). To turn
the handle back again the slide (Item 4) must be
slid in the direction of the arrow again. Please
make sure that the end of the handle audibly
locks into the motor housing.
GB
230V ~ 50Hz
600 W
530 mm
600 mm
20 mm
3200/min
96 dB(A)
88,6 dB(A)
2
4,2 m/s
4,0 kg
15
Werbung
Inhaltsverzeichnis
