Technical Data; Declaration Of Conformity; Starting Operation - Bosch PAS 11-21 Originalbetriebsanleitung

OBJ_BUCH-860-007.book Page 12 Wednesday, July 9, 2014 12:46 PM
12 | English

Technical Data

All-Purpose Vacuum Cleaner
Article number
Rated power input
Power input, max.
Frequency
Container volume (gross)
Dust bag contents
Vacuum, max.*
Airflow, max.*
Weight according to
EPTA-Procedure 01/2003
Protection class
* measured at the blower
The values given are valid for nominal voltages [U] of 230 V. For lower voltage and models for specific countries, these values can vary.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60335-1, EN 60335-2-69.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 13.05.2014
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Note: For vacuuming, the permanent filter 11 always must be
inserted. In addition, the dust bag 14 must be used when dry
vacuuming.
Replacing/Inserting the Dust Bag (see figure A)
– Unlock the latches 4 and remove the vacuum lid 10.
– Pull off the full dust bag 14 from the connection flange to-
ward the rear. Close the opening of the dust bag by folding
down the lid. Remove the closed dust bag from the vacuum
cleaner.
– Slide the new dust bag 14 over the connection flange of the
vacuum cleaner. Make sure that the full length of the dust
1 609 92A 0PY | (9.7.14)
PAS 11-21
0 603 395 034 0 603 395 003
0 603 395 008
0 603 395 032
0 603 395 037
0 603 395 042
W 900
W 1100
Hz 50/60
l 21
l 6
hPa 150
3
m /h 180
kg 6,3
/II
bag 14 faces against the inner wall of the container 5. Re-
attach the vacuum lid 10.
– Lock the latches 4.
When using a dust bag 14, the permanent filter 11 remains
unclogged longer, the vacuuming performance is maintained
longer, and the disposal of dust is made easier.
Mounting the Vacuum Hose (see figure A)
– Insert the vacuum hose 6 into the hose connection piece 8
until it is locked.
– Insert the extension tubes firmly into each other.
– Insert the accessory holder 13 from above onto the holder
of the vacuum lid 10. Afterwards, insert the angle piece in-
to the accessory holder 13 from the bottom until it can be
heard to latch.
– For disassembly of the accessory holder 13, press the
ends of the angle piece together and pull it out towards the
bottom. Remove the accessory holder 13 to the top.
Removing the Vacuum Hose (see figure A)
To remove the vacuum hose 6, press the unlocking button 7
to the left and pull out the vacuum hose 6 at the same time.
Operation

Starting Operation

 Observe the correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the vacuum cleaner. Vacuum cleaners
marked with 220–240 V can also be connected to
220 V
To save energy, only switch the vacuum cleaner on when us-
ing it.
PAS 11-21 PAS 12-27
0 603 395 1..
1100 1100
1300 1300
50/60 50/60
21 27
6 10
150 160
180 216
6,3 6,5
/II /II
PAS 12-27 F
0 603 395 2..
1100
1300
50/60
27
10
160
216
6,5
/I
Bosch Power Tools