Inhaltsverzeichnis
Werbung
18 | English
When changing the application tool, wear protective
u
gloves.Application tools can become hot when used for
prolonged periods of time.
Do not scrape any dampened materials (e.g. wallpa-
u
per) or on damp surfaces. Water entering a power tool
increases the risk of electric shock.
Do not treat the surface you will be working on with
u
any fluids that contain solvents. Poisonous vapours
may develop due to the materials heating up when being
scraped.
Take particular care when handling scrapers and
u
blades. The application tools are very sharp. Danger of in-
jury.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for sawing and cutting wood-
based materials, plastic, plasterboard, non-ferrous metals
and mounting elements (e.g. non-hardened nails, clamps). It
is also suitable for working on soft wall tiles and for dry sand-
ing and scraping of small areas. It is ideal for working close to
edges and flush with surfaces. The power tool must only be
operated using Bosch accessories.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) On/off switch
1 609 92A 8AY | (09.12.2022)
a)
(2) Battery
a)
(3) Battery release button
(4) Ventilation slots
(5) Orbital stroke rate preselection thumbwheel
(6) Handle (insulated gripping surface)
(7) SDS lever for unlocking tools
(8) Tool holder
(9) Worklight
(10) Clamping lever for depth stop
a)
(11) Depth stop
a)
(12) Plunge cut saw blade
a)
(13) Dust extraction system
a)
(14) Sanding plate
a)
(15) Sanding sheet
(16) Clamping lever for dust extraction system
a)
(17) Dust extraction outlet
a)
(18) Dust extraction adapter
a)
(19) Dust extraction hose
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless multi-cutter
Article number
Rated voltage
No-load speed n₀
Oscillation angle on left/right
Weight according to EPTA-Pro-
cedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperature
B)
during operation
and during
storage
Recommended rechargeable
batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
Noise/Vibration Information
Noise emission values determined according
to EN 62841‑2‑4.
Typically, the A-weighted sound pressure level of the power
tool is 80 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
a)
a)
GOP 185‑LI
3 601 HG2 0..
V=
18
−1
min
10000–20000
°
1.7
A)
kg
1.5−2.6
°C
0 to +35
°C
−20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
Bosch Power Tools
Werbung
Inhaltsverzeichnis
