SECU Selo-B V.2 FP Bedienungsanleitung Seite 11

H A U P T M E N U
Codeänderung
Sprache/Language
CODE / Fingerp.:
Administrator...
Display
H A U P T M E N U
Info
Codeänderung
Specifies whether you can use the
Sprache/Language
1: the last entry ( 2: FUNC: ) or switch to the main
Administrator...
H A U P T M E N U
Info
menu ( FUNC: M ).
Codeänderung
Sprache/Language
( ) appears when you can scroll down using
1: Administrator... 2: FUNC:
the "2" key. Info
( ) appears when you can scroll up using
1: 2: FUNC:
the "1" key.
( ) indicates the battery level.
CODE / Fingerp.:
( / ) indicates whether the locking mechanism
has released the lock and the safe can be opened.
CODE / Fingerp.: Bitte Drehknauf
betätigen!
09.08.19 14:50
FUNC: M
FUNC: M
Opening
Opening with PIN code
CODE / Fingerp.: Please turn
the knob!
FUNC: M
• Switch on the lock using the key.
• Enter the 7 or 8-digit PIN code (factory setting "1-2-3-4-5-6-7").
• "Please turn the knob!" appears in the display
• Turn the knob.
Opening with fingerprint
CODE / Fingerp.: Enter next
authorisation
FUNC: M FUNC:
• Switch on the lock using the key.
• Move a programmed finger from the top to bottom centrally over
the sensor.
• The message "Validity not achieved" appears on the display.
• Enter a valid 7 or 8 digit pin code (factory setting "1-2-3-4-5-6-7") of another
user.
• "Please turn the knob!" appears in the display
• Turn the knob.
SECU Selo – B V.2 FP
Closing
key to cancel After the safe has been closed, it is essential that the
M A I N M E N U
rotary knob is moved manually to its initial position.
Code change
Ensure that the rotary knob is in the same position
Language/Sprache
as in the following illustration.
Administrator ...
Info
1: 2: FUNC:
Menu structure
Setting up the menu structure
CODE / Fingerp.:
• Change code
• Language
• Administrator
FUNC: M
Please turn
the knob!
• Info
> User
> Create
> Create code
> Create fingerprint
> Assign
> Assign code
> Assign fingerprint
> Delete
> Time functions
> Set time
> Set date
> Automatic ST/WT
> Delay time
> Programming
> Firmware update
> Reorganise
> Processes
> Display
> Save
> Code length
> Setup
> Register
> FP reset
> System info
> System check
Description of the menu functions
Code Change menu
Change the administrator code and the user codes.
We would like to point out that, for security reasons,
the factory-set administrator code must be changed
to an individually set code.
• Switch on the lock using the - key.
• Then press .
• The "Main menu" appears.
• Confirm with .
• You can use the keys 1 or 2 to scroll until the
administrator/user is displayed and you wish
to change the code for.
• Confirm with .
• Enter the old or factory code that was previously
valid using the keypad and press .
• Enter the new code using the keypad and
confirm with .
• Repeat your entry and confirm it again with .
• "Code change completed" is displayed after
a correct entry.
• Press any key.
Note: When a safe lock is first started up, additional
information on the current date and time are
requested:
• Enter the day (2 digits)
• Enter the month (2 digits)
• Enter the year (2 digits)
• Enter the hour (2 digits)
• Enter the minutes (2 digits)
M A I N M E N U
Code change
Language/Sprache
Administrator ...
Info
2: FUNC:
New Code:
FUNC: M
Code change
completed!
FUNC:
English I 11