Bosch GWX 18V-10 P Professional Originalbetriebsanleitung Seite 23

requirements of the operation. To do this, push the unlock-
ing lever (1) upward and rotate the protective guard (10)
into the required position.
Always position the protective guard (10) such that
u
the two cams on the unlocking lever (1) engage in the
corresponding openings on the protective guard (10).
Adjust the protective guard (10) such that sparking in
u
the direction of the operator is prevented.
The protective guard (10) must only be adjustable
u
while the unlocking lever (1) is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note: The coding cams on the protective guard (10) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
Always use the protective guard for cutting (11) when
u
cutting with bonded abrasives.
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (11) is fitted in the same
way as the protective guard for grinding (10).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (25) is fit-
ted in the same way as the protective guard for grinding
(10).
Hand guard
Always fit the hand guard (18) when working with the
u
rubber sanding pad (19) or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard (18) to the side handle (8).
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle (8)/(9) on the right or left of the
machine head depending on the working method.
Do not operate your power tool without the auxiliary
u
handle (8)/(9).
Do not continue to use the power tool if the auxiliary
u
handle (8)/(9) is damaged. Do not make any altera-
tions to the auxiliary handle (8)/(9).
fortably.
Fitting and removing abrasive tools
Follow the special assembly instructions for
X-LOCK application tools.
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Bosch Power Tools
The low-vibration auxiliary
handle (9) reduces vibra-
tion, enabling the tool to be
used safely and more com-
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Only use original X-LOCK application tools that carry the
u
X-LOCK logo. A maintained clamping gauge of max.
1.6 mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
ure clamping, potentially causing the clamp tool to come
loose.
X-LOCK application tools do not need additional clamping
u
flanges or support flanges.
Make sure that the application tool and the holder are not
u
deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that both X-LOCK catches are open (see figure
below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK
catches.
Fitting the abrasive tool
➊ Place the grinding/cutting/flap disc in a central position
on the X-LOCK holder, parallel to the bearing surface
and with the right side facing up.
➋ Push the disc into the holder.
➌ The disc audibly clicks into place. Do not actuate the
lever (3) when doing so.
(3)
After fitting, check that the edge of the abrasive tool
u
(➍) is fitted correctly, i.e. is no higher than the refer-
ence surface (➎). If the edge is higher than the refer-
ence surface, either the holder must be cleaned or the
abrasive tool must not be used.
Before removing the grinding/cutting/flap disc: Make
sure that the power tool has come to a complete stop.
English | 23
1 609 92A 7ZU | (30.08.2022)