Technical Data; Noise/Vibration Information - Bosch GWX 18V-10 P Professional Originalbetriebsanleitung

(19) X-LOCK backing pad for fibre discs
a)
(20) X-LOCK fibre disc
(21) X-LOCK clip for fibre discs
a)
(22) X-LOCK cup brush
a)
(23) X-LOCK conical brush
(24) X-LOCK diamond core cutter
(25) Extraction guard for cutting with cutting guides
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Angle Grinder
Article number
Rated voltage
A)
Rated no-load speed
Max. grinding disc diameter/
rubber sanding pad diameter
Kickback stop
Restart protection
Run-out brake
Weight according to EPTA-
B)
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Compatible rechargeable
batteries
Recommended rechargeable
batteries
Recommended chargers
A) Rated no-load speed for the selection of appropriate grinding
tools in accordance with EN 60745. The actual speed is lower
for safety reasons.
B) Depends on rechargeable battery, protective guard, and auxili-
ary handle in use
C) Limited performance at temperatures < 0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 82
dB(A); sound power level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Bosch Power Tools
a) Surface grinding (roughing) and abrasive cutting:
a
h
Disc sanding:
a)
a
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
a) cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
a)
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
GWX 18V-10 P
ing period.
3 601 JJ4 2.. To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
V= 18
tually being used should also be taken into account. This can
–1
min 9,000
significantly reduce the exposure to vibration over the total
mm 125 working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
●
power tool and application tools, keeping the hands warm,
●
and organising workflows correctly.
●
Kickback control
kg 2.5–3.3
°C 0 to +35
°C –20 to +50
To restart the tool, set the On/Off switch (6) to the "off" po-
sition and then switch the power tool on again.
GBA 18V...
Restart protection
ProCORE18V...
The restart protection feature prevents the power tool from
GBA 18V...
uncontrolled starting after the power supply to it has been
≥ 4.0Ah
interrupted.
ProCORE18V...
To restart the tool, set the on/off switch (6) to the off posi-
≥ 4.0Ah
tion and then switch the power tool on again.
GAL 18...
GAX 18...
X-LOCK run-out brake
GAL 36...
triggered, the power tool will brake even faster than this.
Drop control
CONTROL
2 2
= 6.0 m/s , K = 1.5 m/s ,
2 2
= 3.0 m/s , K = 1.5 m/s .
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
The power tool is fitted with an electronic run-
out brake. When the power supply is switched
off or interrupted, the abrasive tool is brought
to a complete stop within a few seconds. When
Drop Control or Kickback Control are
The integrated impact shutdown switches the
power tool off as soon as it hits the floor. To re-
start the tool, set the on/off switch (6) to the
DROP
"off" position and then switch the power tool on
again.
1 609 92A 7ZU | (30.08.2022)
English | 21