Maintenance And Service; Maintenance And Cleaning - Bosch GPO 14 CE Professional Originalbetriebsanleitung

OBJ_BUCH-1284-003.book Page 17 Tuesday, December 16, 2014 4:09 PM
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To save energy, only switch the power tool on when using it.
To start the power tool, press the On/Off switch 5 forward
and then down.
To lock-on the pressed On/Off switch 5, push the On/Off
switch 5 further forward.
To switch off the power tool, release the On/Off switch 5, or
when it is locked, briefly press the On/Off switch 5 and then
release it.
 Check grinding tools before using. The grinding tool
must be mounted properly and be able to move freely.
Carry out a test run for at least one minute with no load.
Do not use damaged, out-of-centre or vibrating grind-
ing tools. Damaged grinding tools can burst and cause in-
juries.
Speed preselection
The required speed can be preselected with the thumbwheel
4 (also while running).
The required speed depends on the material and the working
conditions and can be determined through practical testing.
Thumbwheel Position No-load speed (min
1 750
2 1200
3 1600
4 2000
5 2400
6 3000
Constant Electronic Control
Constant electronic control holds the speed constant at no-
load and under load, and ensures uniform working perfor-
mance.
Working Advice
 Before any work on the machine itself, pull the mains
plug.
 Clamp the workpiece if it does not remain stationary
due to its own weight.
 Do not strain the machine so heavily that it comes to a
standstill.
 After heavily straining the power tool, continue to run
it at no-load for several minutes to cool down the acces-
sory.
Bosch Power Tools
For sanding applications on soft materials, e. g., gypsum or
paint, it is recommended to use the rubber sanding plate 18
with sanding sheet 19.
Cup brushes 21 and wheel brushes are suitable for rust re-
moval.
Polishing
For the polishing of weathered paint or buffing out scratches
(e.g., acrylic glass), the machine can be equipped with appro-
priate polishing accessories such as lamb's wool bonnet, pol-
ishing felt or sponge (accessories).
Select a low speed for polishing (stage 1 – 2) in order to avoid
excessive heating of the surface.
Apply the polish onto a somewhat smaller surface than you in-
tend to polish. Work the polishing agent in with a suitable pol-
ishing tool applying it crosswise or with circular motion and
moderate pressure.
Do not allow the polishing agent to dry out on the surface, oth-
erwise the surface can become damaged. Do not subject the
surface to be polished to direct sunlight.
Clean the polishing accessories regularly to ensure good pol-
ishing results. Wash out polishing accessories with a mild de-
tergent and warm water; do not use paint thinner.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
-1
)
 For safe and proper working, always keep the machine
and ventilation slots clean.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
Please store and handle the accessory(-ies) carefully.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
English | 17
1 609 92A 114 | (16.12.14)