Morphy Richards Cascata Bedienungsanleitung Seite 4

47140MEE Rev1_9225 47507 MEE pump - Jon 25/01/2012 20:57 Page 4
g
Features
A
(1) Spout
(2) Jug
(3) Water Tank
(4) Concealed Element
(5) Base Unit
(6) Control Panel
(7) Cord Storage (underneath)
(8) Lid
(9) Washable Filter
(10) Filter Holder
(11) Water Hole (in Filter Holder)
(12) Water Nozzle
(13) 360° Connector
(14) Strength Selector
(15) 85° Temperature Button
(16) 95° Temperature Button
(17) On/Off / Start Button
(18) Vent
(19) Spoon
Using your Cascata
1
Twist to remove the Lid (8). Remove the Washable Filter (9) and
Filter Holder (10) from the Jug.
2
Fill the Water Tank (3) with the required amount of water. Do not fill
above the max line.
3
Place the coffee grinds in the Washable Filter (9). Use 1 spoon (19)
or 7g of coffee per cup. Place the Washable Filter back into the
Filter Holder (10).
4 Place the Filter Holder into the Jug. Ensure the Water Hole (11) is
correctly aligned with the Water Nozzle (12), otherwise the
Cascata will not operate correctly.
5 Place the Jug onto the Base Unit (5) and replace the Lid (8), twist
to lock. Ensure the Lid is securely fitted before operating.
6
Attach to a mains supply, the Cascata will beep twice. Press the
On/Off Button (17). The On/Off and 95o Temperature Button (16)
will illuminate.
7 Use the Strength Selector (14) to select the desired strength of the
coffee. Then select the desired water temperature (15),(16). The
selected button will illuminate.
8
Press the On/Off / Start Button (17) to begin brewing coffee.
When completed, the On/Off / Start Button will illuminate red,
your Cascata will beep and switch to the keep warm mode.
4
Before first use
Fill the Water Tank (3) with water to the MAX mark, and place
onto the Base Unit. Ensure the Water Hole (11) is correctly
aligned with the Water Nozzle (12), otherwise the Cascata will
not operate correctly. The Cascata will beep twice when
plugged into the mains. Press the On/Off / Start Button (17), set
the Strength Selector (14) to maximum, then press the 95o
Temperature Button (16). Press the On/Off / Start Button (17) to
activate the brewing process and wait for the water to heat up
and flush through the system. The On/Off / Start Button will
illuminate red when the brewing process has been completed,
dispose of the boiled water.
Keep warm
Your Cascata Filter Coffee Maker features a keep warm setting
which will keep your coffee warm for 1 hour after brewing is
complete. The keep warm setting will work only when the Jug is
sat on the Base Unit.
The keep warm setting has a default temperature of 85°.
To adjust the keep warm temperature to 95° press the 95°
Temperature Button (16).
To switch the keep warm setting off, press the On/Off Start
Button (17).
Cleaning your Cascata
• IMPORTANT: Never wash your Cascata Filter Coffee Maker in
a dishwasher.
• In order to reduce staining, we recommend that your Cascata
Filter Coffee Maker is cleaned after every use.
• Thoroughly wash the Jug and all of its brewing components with
warm water. Do not immerse the jug into the water.
• To remove any stubborn stains from your Cascata Filter Coffee
Maker we recommend that you use a sterilising fluid, (found in the
baby aisle of supermarkets and pharmacies.)
1 Add 7ml of sterilising fluid to the unit and fill to the top of Water
Tank with warm water and leave for 30 minutes, using a plastic
kitchen brush to gently agitate the stained areas if required.
2 When using the plastic kitchen brush care must be taken around
the vent dome on the element to prevent dislodging/damage.
3 For stubborn stains it may be necessary to repeat this process 2
to 3 times.
4 Once complete, rinse the unit thoroughly with warm water and
then run the brewing cycle with clean water only & repeat 2-3
times. If there is any residual taste from the cleaning product
repeat the rinsing process again.
• For general cleaning wipe outer surfaces with a soft damp cloth,
care must be taken when cleaning to ensure no electrical
connections make contact with water. Do not immerse in water.