Maintenance And Service; Maintenance, Cleaning And Storage; After-Sales Service And Application Service - Bosch UniversalRotak 2x18V-37-550 Originalbetriebsanleitung

Problem Possible Cause
Machine functions in- Internal wiring of garden tool defective
termittently
Motor protector has activated
Machine leaves ragged Height of cut too low
finish
Cutting blade blunt
and/or
Possible clogging
Motor labours
Blade fitted upside down
Blade not rotating Cutting blade obstructed
while garden product
switched on
Blade nut/bolt loose
Excessive vibrations/ Blade nut/bolt loose
noise
Cutting blade damaged

Maintenance and Service

Maintenance, Cleaning and Storage

Before any work on the garden product itself (e. g.
u
maintenance, tool change, etc.) as well as during
transport and storage, remove the batteries from the
garden product. There is danger of injury when uninten-
tionally actuating the On/Off switch.
For safe and proper working, always keep the product
u
clean.
Maintenance of both batteries
Use the following procedures to enable optimum usage of
the batteries:
– Protect the batteries against moisture and water.
– Store the machine and batteries only within a temperat-
ure range between –20 °C and 50 °C . As an example, do
not leave the batteries in the car in summer.
– The batteries must not be stored within the product but
stored separately.
– Do not leave the batteries in the product in direct sun-
light.
– The ideal storage condition for the batteries is 5 °C.
– Occasionally clean the venting slots of the batteries using
a soft, clean and dry brush.
A significantly reduced working period after charging indic-
ates that the batteries are used and must be replaced.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
Bosch Power Tools
Corrective Measure
Contact Bosch customer service agent
Allow motor to cool and increase height of cut
Increase height of cut
Replace cutting blade (see figure K).
Switch garden tool off and disengage isolator key
Check underneath the garden product and clear
out as necessary (always wear protective gloves)
Refit blade correctly
Switch garden tool off and disengage isolator key
Clear obstruction (always wear protective gloves)
Tighten blade nut/bolt (22 Nm)
Tighten blade nut/bolt (22 Nm)
Replace cutting blade (see figure K).
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
Disposal
Products, rechargeable batteries, accessories
and packaging are to be recycled in an environ-
mentally friendly manner.
English | 17
F 016 L94 513 | (02.03.2023)