Specifications; Specific Safety Rules - Makita 6951 Betriebsanleitung

ENGLISH
1 Bit
2 Sleeve
3 Switch trigger
4 Reversing switch lever

SPECIFICATIONS

Model
Capacities
Machine screw ........................................ 4 mm – 8 mm
Standard bolt ........................................ 6 mm – 12 mm
High tensile bolt .................................... 6 mm – 12 mm
Wood screw/Lag screw
(length) ............................................. 30 mm – 120 mm
–1
No load speed (min ) ...................................... 0 – 2,200
Impacts per minute ........................................... 0 – 3,000
Max. fastening torque .................................. 1,000 kg•cm
Overall length ..................................................... 239 mm
Net weight .............................................................. 1.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated
adherence to impact driver safety rules. If you
use this tool unsafely or incorrectly, you can
suffer serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Wear ear protectors.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious per-
sonal injury.
Explanation of general view
5 Clockwise rotation
6 Counterclockwise rotation
7 Seconds
8 Fastening time
6951
GEB012-2
use) replace strict
9
10 Limit mark
11 Screwdriver
12 Brush holder cap
OPERATING INSTRUCTIONS
Installing or removing bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Use only the driver bit or socket bit shown in Fig. 1.
Do not use any other driver bit or socket bit.
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will go.
Then release the sleeve to secure the bit. (Fig. 2)
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
If the bit is not inserted deep enough into tne sleeve, the
sleeve will not return to its original position and the bit will
not be secured. In this case, try re-inserting the bit
according to the instructions above.
Switch action (Fig. 3)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Reversing switch action (Fig. 4)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
Operation (Fig. 5)
Place the point of the driver bit in the screw head.
Apply forward pressure to the tool to the extent that the
bit will not slip off the screw. Start the tool slowly and then
increase the speed gradually. Release the trigger just as
the screw bottoms out. The proper fastening torque dif-
fers depending upon the kind or size of screws/bolts, the
type of materials to be fastened, etc. Refer to Fig. 5 for
the relation between fastening time and wood screw size.
(Material to be fastened: Lauan)
Wood screw/Lag screw size
3