Blowing In Confined Spaces - Makita DAS180 Betriebsanleitung

Blowing in confined spaces

Recommended nozzles
—
Nozzle 3
Blow into confined spots, corners, and spaces by the
walls to dust off.
Point the nozzle straight at spaces at a reasonable
distance and squeeze the switch trigger to control blow-
ing air volume.
► Fig.26
► Fig.27
CAUTION:
Keep the nozzle away a reasonable
distance from blowing spots to avoid blowing up
dust into the air.
CAUTION:
Use personal protective equip-
ment such as a dust mask and eye protection.
NOTICE:
Avoid blocking the air vent holes
around the blower outlet. It otherwise may cause
sudden noise and vibrations and could possibly affect
the tool performance.
► Fig.28: 1. Air vent holes 2. Blower outlet
Dusting air filter
Recommended nozzles
—
Nozzle 7
Dust filter surfaces by blowing air through one side of
the filter to the other.
Direct the nozzle on filter surfaces within a short dis-
tance and swing it from side to side to blow dust away
from surfaces.
► Fig.29
CAUTION:
Use personal protective equip-
ment such as a dust mask and eye protection.
NOTE: Point the nozzle at an angle according to the
outlines of the filter so the adhered dust can be easily
removed.
Blowing wide and open area
Recommended nozzles
—
Wide range nozzle
Blow air over dirt and liquid on wide-open surfaces such
as desktop and floor, using the five-hole nozzle with 120
degree range of blowing.
Direct the nozzle over a large area within a certain
distance and swing it back and forth and from side to
side to blow widely.
► Fig.30
CAUTION:
Use personal protective equip-
ment such as a dust mask and eye protection.
Inflating plastic inflatables
Recommended nozzles
—
Pinch valve nozzle
—
Nozzle 13
Inflatable air volume with fully charged battery
cartridge BL1860B without recharging it
Air volume mode
4: Max
3: High
2: Medium
1: Low
NOTE: The maximum output air pressure of this tool is 20.2 kPa.
(With nozzle 13)
Inflate beach toys, pillows, and similar small plastic
inflatables with pinch valve nozzle.
Inflate garden pools, air mattresses, and similar large
plastic inflatables with nozzle 13.
Insert the nozzle into an air inlet on an inflatable item
and pull the switch trigger to start inflating.
Slowly release the switch trigger to reduce air volume as the inflat-
able item comes close to fully inflated. Remove the nozzle from
the air inlet after stopping the air flow and then close the air inlet.
► Fig.31
► Fig.32
CAUTION:
Always be careful not to over-in-
flate inflatables during operation. It otherwise may
burst the inflatables, possibly causing damage to the
tool and personal injury.
CAUTION:
Never leave the tool unattended
while the nozzle is attached to inflatables or
during operation.
CAUTION:
Be aware that heated air stream
may flow through the air vent hole at bottleneck
of the pinch valve nozzle due to air circulation.
NOTE: Make sure to insert the pinch valve nozzle
fully through the air inlet so the nozzle head serves to
open the flap valve inside the air inlet.
NOTE: For an inflatable item with a small air inlet
opening, insert the narrow tip of the pinch valve noz-
zle in the air inlet until the bottleneck of the nozzle
head touches the rim of the air inlet.
NOTE: For an inflatable item with a large air inlet
opening, insert the pinch valve nozzle head fully into
the air inlet to open the flap valve inside the air inlet.
► Fig.33: 1. Flap valve 2. Small air inlet opening 3. Large
air inlet opening 4. Bottleneck 5. Air vent hole
NOTE: If an air inlet on an inflatable item is relatively
smaller than the pinch valve nozzle head, squeeze
and enlarge the air inlet by hand and then twist and
hold the nozzle head into the air inlet.
19 ENGLISH
Number of ø61 cm
Inflatable air plastic beach balls
volume equivalent in air
(With pinch valve volume
nozzle) (With pinch valve
nozzle)
3
13.0 m 110
3
13.4 m 115
3
15.6 m 130
3
22.8 m 190