Technical Data - Niko 350-20065 Handbuch

350-20065
5. MAINTENANCE
Dirt may prevent the presence detector from functioning properly. Therefore, always keep the lens clean and
dry. Use a damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens
clean. If the lens or other parts of the presence detector are defective, please contact an authorised installer.
6. TROUBLESHOOTING
Problem Cause
The lighting is not switched on. Incorrect wiring.
The ambient light level is too
high.
The lighting is not switched off. The switch-off delay is too long.
Detector has false triggering.
Incorrect wiring.
The red LED does not turn on. PIR is not selected as the
detection method.
The movement is outside the
detection range of the PIR sensor.
A cover cap is used so that there
is no detection on the place of the
movement.
The green LED does not turn on. US is not selected as the
detection method.
The movement is outside the
detection range of the ultrasonic
sensor.
False triggering The following elements may
affect the proper functioning of
the ultrasonic sensor and may
cause false triggering:
- air flows
- sound absorbing materials,
carpet, curtains, ...
- heat sources
- reflective objects
- objects subject to wind
- wiring (a reverse wiring between
N and L will cause reduced
sensitivity of the ultrasonic
sensor sensitivity and will limit
the detection area)

7. TECHNICAL DATA

dimensions
power supply voltage
circuit breaker
power consumption
relay contact
maximum load
maximum switching capacity
maximum inrush current
detection angle
mounting height
detection range
light sensitivity
switch-off delay
protection degree
protection class
ambient temperature
cable inlet
quality mark
accessories
* The MCB rating is limited by national installation rules.
10
Action
Refer to the wiring diagrams and
check if the lighting is working.
Check the set lux value and
adjust if necessary (higher value).
Check the switch-off delay and
adjust if necessary (lower value).
Check for any objects in the room
that may cause false triggering
and remove them from the
detection area.
Check the wiring diagrams.
Select PIR as the detection
method.
The movement should be within
the detection range (8 m).
Remove or reposition the cover
cap.
Select US as the detection
method.
The movement should be within
the detection range (16 x 10 m).
- Activate the potentiometer for
light sensitivity (ON). This will
reduce the sensitivity of the
ultrasonic sensor by ± 10 to
40%, depending on the severity
of the air flow.
- Avoid aiming the detector
toward any heat sources, such
as air conditioning, electric fans,
heaters or reflective surfaces.
- Make sure there are no objects
within the detection range that
are subject to wind.
- Check the wiring diagrams.
60 x 120 mm (HxW)
230 Vac ± 10%, 50 Hz
maximum MCB rating 10 A*
1 W
NO (max. 10 A, 230 V), potential-free, light- and
motion-sensitive
incandescent lamps (2300 W)
230 V halogen lamps (2300 W)
all low-voltage halogen lamps (1200 W)
fluorescent lamps (non-compensated) (1200 VA)
economy lamps (CFLi) (350 W)
led lamps 230 V (350 W)
140 μF
165 A/20 ms or 800 A/200μs
360°
2 – 3 m
US: 12 x 19 m
PIR: ø 9,5 m
10 – 1000 lux
1 – 30 min
IP20
class I devices
0 – 45°C
2 x 12 mm
CE marked in compliance with EN 60669-2-1
IR remote control (350-20067)
Warnings regarding installation
The installation of products that will permanently be part of the electrical installation and which include dangerous
voltages, should be carried out by a qualified installer and in accordance with the applicable regulations. This
user manual must be presented to the user. It should be included in the electrical installation file and it should be
passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.
CE marking
This product complies with all of the relevant European guidelines and regulations. For radio equipment Niko llc
declares that the radio equipment in this manual conforms with the 2014/53/EU directive. The full text of the
EU declaration of conformity is available at www.niko.eu under the product reference, if applicable.
Environment
This product and/or the batteries provided cannot be disposed of in non-recyclable waste. Take your discarded
product to a recognised collection point. Just like producers and importers, you too play an important role in
the promotion of sorting, recycling and reuse of discarded electrical and electronic equipment. To finance the
rubbish collection and waste treatment, the government levies recycling charges in certain cases (included in
the price of this product).
PM350-20065R23065