Inhaltsverzeichnis
Werbung
12 | English
Technical Data
Rainwater Pump
Article number
Flow rate (Q)
Head pressure (H)
max. submersion depth
max. water temperature
Rated voltage
Water Ingress Protection
Weight according to EPTA‑Procedure
Serial number
Recommended ambient temperature during char-
ging
Permitted ambient temperature during operation
and storage
Battery type
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
The pump should only be used with the, GardenPump 18, battery control unit.
Assembly
Fastening the Wall Attachment/Water Tank
Attachment (see figure B)
Fasten the wall attachment (10) next to the water tank. Note
that the distance to the water tank is limited due to the con-
necting cable length.
The distance to the water tank plus the water tank height
may not be larger than the length of the connecting cable.
When mounting the wall attechment to the wall, use the
guide holes to mark the position of the screws.
If wall mounting is not possible, the provided water tank at-
tachment (8) can be attached directly to the rim of the water
tank.
NOTE: The battery control unit is switched off via a thermal
switch at increased temperature. The attachment for the
battery control unit should therefore be mounted in a
shaded position.
Inserting/Removing the Battery Control Unit
(see figure C)
In the case of wall attachment take out the securing
screw (9) from the attachment, attach the battery control
unit (6) from above into the wall attachment and secure it at
the bottom with the clip and securing screw (9).
In case of water tank attachment just clip the battery control
unit on the attachment.
F 016 L94 292 | (07.02.2023)
l/h
m
m
°C
A)
kg
°C
B)
°C
Determining the required length of cable and
connecting hose (see figure D)
Note: The pump needs to be positioned 50 mm above the
base of the tank, clear of any sediment that might damage
the pump.
Measure the height H and the diameter D of the water tank
as well as the distance E from the rim of the tank to the bat-
tery control box.
The length L
H + D + E – 250 mm
The length L
H – 130 mm
Wrapping the cable and cutting the connecting
hose (see figure E)
Wrap the excess cable around the pump (18) and secure us-
ing the provided cable clamp (16).
Release the anti-siphon connector (12) with hose attached
from the clamp on the hose guide (11).
Cut the connecting hose to length L
siphon connector (12) on the remaining connecting hose.
Return the anti-siphon connector (12) with hose into the
clamp on the hose guide (11).
You can leave the connecting hose uncut and let the hose
protrude. Please note that for the anti-siphon connector to
function the anti-siphon connector needs to be placed in its
original position in the hose guide.
GardenPump18V-2000
Pump
3 600 HC4 1..
1800
17.5
1.8
35
V
18
IPX8
0.8
see type plate on tool
0... +35
-20... +50
PBA 18V...W-.
1.5 Ah, 2.0 Ah, 2.5 Ah,
1.5 Ah, 2.0 Ah, 2.5 Ah,
3.5 Ah, 4.0 Ah, 6.0 Ah
of the cable calculates as follows:
1
of the connecting hose calculates as follows:
2
and re-attach the anti-
2
Battery Control Unit
3 600 HC4 0..
18
IPX4
0.6
see type plate on tool
0... +35
-20... +50
PBA 18V...W-.
3.5 Ah, 4.0 Ah, 6.0 Ah
Bosch Power Tools
Werbung
Inhaltsverzeichnis
