Functional Description - Makita PC5000C Betriebsanleitung

29. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
30. Do not use the tool on any materials containing
asbestos.
31. Do not use water or grinding lubricant.
32. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become necessary to clear dust, first disconnect
the tool from the mains supply (use non metallic
objects) and avoid damaging internal parts.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
For tool with the lock-on switch
To start the tool, simply pull the switch trigger (A).
Release the switch trigger to stop. For continuous
operation, pull the switch trigger (A) and then push in the
lock lever (B). To stop the tool from the locked position,
pull the switch trigger (A) fully, then release it.
For tool with the lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided. To start the tool, push in the lock
lever (B) and then pull the switch trigger (A). Release the
switch trigger to stop.
For tool with the lock on and lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided. To start the tool, push in the lock
lever (B) and then pull the switch trigger (A). Release the
switch trigger to stop. For continuous operation, push in
the lock lever (B), pull the switch trigger (A) and then push
in the lock lever (B) further. To stop the tool from the
locked position, pull the switch trigger (A) fully, then
release it.
Electronic function
Constant speed control
• Possible to get fine finish, because the rotating speed
is kept constantly even under the loaded condition.
• Additionally, when the load on the tool exceeds
admissible levels, power to the motor is reduced to
protect the motor from overheating. When the load
returns to admissible levels, the tool will operate as
normal.
Soft start feature
• Soft start because of suppressed starting shock.
Indication lamp (Fig. 2)
The indication lamp lights up green when the tool is
plugged. If the indication lamp does not light up, the mains
cord or the controller may be defective. The indication
lamp is lit but the tool does not start even if the tool is
switched on, the carbon brushes may be worn out, or the
controller, the motor or the ON/OFF switch may be
defective.
Unintentional restart proof
Even lock lever keeping the switch trigger depressed
(Lock-on position) does not allow the tool to restart even
when the tool is plugged.
At this time, the indication lamp flickers red and shows the
unintentional restart proof device is on function.
To cancel the unintentional restart proof, pull the switch
trigger fully, then release it.
Level planing (for PC5001C only) (Fig. 3)
To level a surface, the base of the planer should be
aligned with the diamond wheel. The front roller should be
adjusted (use hex wrench) upward to the level required for
the desired stock removal amount.
To change the amount of stock (concrete) removed,
loosen the hex socket head bolts on the base holder with
the hex wrench. Raise or lower the front roller to adjust
the gap between it and the diamond wheel. The difference
is the stock removal amount. Then secure the hex socket
head bolts very carefully. (Fig. 4)
NOTE:
• Maximum stock removal should be less than 4.0 mm.
Tilting base for smoother planing (for
PC5001C only) (Fig. 5)
For smooth removal of a given surface roughness or
texture, tilting the base is helpful. Use the hex wrench to
loosen the two hex socket head bolts securing the base
on either side.
Use a hex wrench to lower the three hex socket head
bolts on the base by turning them on the base clockwise.
(Fig. 6)
Use a square or ruler to obtain the desired base angle in
relation to the diamond wheel. Then secure carefully the
hex socket head bolts on either side of the base. Adjust
center of base near wheel so that it is on the same level
as the wheel. (Fig. 7)
NOTE:
• After base adjustment, turn the three hex socket head
bolts on the base counterclockwise until the heads are
flush with the back side of the base. Turn gently or
base adjustment will be thrown off.
Base adjustment to compensate for wheel
wear (for PC5001C only)
With long use, the diamond wheel will wear and thus
create a gap with the planing surface so that performance
7