Makita DFT087F Betriebsanleitung Seite 9

Adjusting the fastening torque
When you wish to drive machine screws, hex bolts,
etc. with the predetermined torque, adjust the fastening
torque as follows.
CAUTION:
When adjusting the fastening
torque, remove the battery cartridge (excluding
the process of working with the battery cartridge
attached).
1. Open the change plate by hand so that you can
see a hole.
► Fig.7: 1. Change plate
2. Pull the switch trigger and release it so that the
adjust ring rotates and the hole becomes visible. And
then remove the battery cartridge.
3. Use an optional adjust grip to adjust the fastening
torque. Insert the pin of the adjust grip into the hole
in the front of the tool. And then, turn the adjust grip
clockwise to set a greater fastening torque, and coun-
terclockwise to set a smaller fastening torque.
► Fig.8: 1. Adjust grip 2. Hole for adjust grip
4. Insert the battery cartridge and be sure that a
fastening torque has been set up by using a fastening
torque tester.
CAUTION:
Remove the adjust grip before
turning on the power of the tool.
5. Close the change plate by hand securely.
Adjusting no-load speed and
revolution angle etc.
You can adjust the no-load speed, number of turn, etc.
of the tool with your computer. Install the application
software in your computer and connect it to the tool with
an USB cable.
► Fig.9: 1. USB port 2. USB cover 3. USB cable
NOTICE:
Make sure that the USB cover closed
when fastening.
NOTE: Use the Makita genuine USB cable to con-
nect your computer to the tool. Refer to the section
"SPECIFICATIONS".
NOTE: For the application software, please contact
Makita sales representative.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/socket bit
► Fig.10
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
socket bit.
For tool with shallow driver bit hole
A=12mm
B=9mm
For tool with deep driver bit hole
A=17mm
B=14mm
A=12mm
B=9mm
Procedure 1
For tool without one-touch type sleeve
► Fig.11: 1. Driver bit 2. Sleeve
To install the driver bit, pull the sleeve in the direction of the
arrow and insert the driver bit into the sleeve as far as it will go.
Then release the sleeve to secure the driver bit.
For tool with one-touch type sleeve
To install the driver bit, insert the driver bit into the
sleeve as far as it will go.
Procedure 2
In addition to Procedure 1, insert the bit-piece into the
sleeve with its pointed end facing in.
► Fig.12: 1. Driver bit 2. Bit-piece 3. Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case, try re-inserting the bit according to the instruc-
tions above.
NOTE: When it is difficult to insert the driver bit, pull
the sleeve and insert it into the sleeve as far as it will
go.
NOTE: After inserting the driver bit, make sure that it
is firmly secured. If it comes out, do not use it.
Installing hook
Optional accessory
The hook is useful to hang the tool. Install the hook to
the holes on the tool body.
► Fig.13: 1. Hook 2. Hole
9 ENGLISH
Use only these type of driver
bit. Follow the procedure
1. (Note) Bit-piece is not
necessary.
To install these types of driver
bits, follow the procedure 1.
To install these types of driver
bits, follow the procedure 2.
(Note) Bit-piece is necessary
for installing the bit.