Tauch- ⁄ einschraub- ⁄ kanal-temperaturfühler, mit passivem ausgang (15 Seiten)
Inhaltszusammenfassung für Sauter EGT301F902
Seite 1
Istruzioni per l'uso e per il montaggio Sonda di temperatura esterna ⁄ sonda di temperatura per ambienti umidi, con uscita passiva Sauter Italia S.p.A. Via Dei Lavoratori, 131 20092, Cinisello Balsamo Italia Tel. +39 022 80481...
Seite 2
D G F I EGT301F902 Maßzeichnung EGT301F902 Dimensional drawing Plan coté Disegno quotato M16x1.5...
EGT301F902 Rev. 2021 - V15 Außenwandwiderstandsthermometer mit passivem Ausgang, 1x Zweileiterschaltung mit Gehäuse aus schlagzähem Kunststoff und Schnellverschlussschrauben. Er dient zur Erfassung der Außentemperatur, der Temperatur im Feuchtraumbereich, z.B. als Außen fühler, Witterungsfühler, zur Montage auf Außenwänden, in Hallen, im Industriebereich und in der Landwirtschaft.
Allgemeine Informationen Aufbau der Temperaturfühler allgemein: Die Fühler werden wie folgt nach Bauformen unterschieden: Anlegetemperaturfühler, Kabeltemperaturfühler, Gehäuse- und Einbautemperaturfühler. – Bei den Anlegetemperaturfühlern besitzt der Temperaturfühler mindestens eine Anlegefläche, die z.B. an Rohroberflächen oder Heizkörpern angelegt werden muss. Wird die Anlegefläche nicht richtig zur Messoberfläche positioniert, so können erhebliche Temperaturmessfehler entstehen. Es ist für eine gute Kontaktfläche und Temperaturleitung zu sorgen, Schmutz und Unebenheiten sind zu vermeiden, ggfl.
Seite 5
Abweichungen zur Katalog dar stellung sind nicht zusätzlich auf- thermischen Belastungsgrenzen der Schutzrohre nach DIN 43763 geführt und im Sinne des technischen Fortschritts und der stetigen Ver- bzw. nach speziellen Sauter-Standards! besserung unserer Produkte möglich. Bei Veränderungen der Geräte durch Hinweise zum Prozessanschluss von Einbaufühlern: den Anwender entfallen alle Gewährleistungs - an sprüche.
EGT301F902 Rev. 2021 - V15 Outside wall resistance thermometer with passive output, 1x two-wire connection housing made of impact-resistant plastic and quick-locking screws. It is used to measure outside temperatures, temperatures in wet room areas, e.g. as a weather sensor, for installation on outside walls, in halls, in the industrial sector and in agriculture.
Seite 7
General notes Design of temperature sensors in general: Sensors are distinguished by shape type as follows: surface-contacting sensors, cable temperature sensors, and housing-type and built-in temperature sensors. – On surface-contacting sensors, the temperature sensor has at least one contact area that must be brought in contact, e.g. with the surface of radiators or pipes.
Seite 8
DIN 43763 respectively according explicitly mentioned and are possible in terms of technical progress and to specific Sauter standards! continuous improvement of our pro ducts. In case of any modifications made Notes regarding process connection of built-in sensors: by the user, all warranty claims are forfeited.
EGT301F902 Rev. 2021 - V15 Thermomètre à résistance pour mur extérieur avec sortie passive, 1 x 2 fils boîtier en matière plastique résiliente et vis de fermeture rapide. Pour mesurer la température extérieure, la température dans la zone du local humide, par ex.
Généralités Modes de réalisation des sondes de température pour applications en général: On distingue les sondes suivant leur forme de construction, à savoir: sondes de température à applique, sondes de température à câble, sondes de tempéra- ture sous forme de boîtier et sondes de température pour montage en gaine. –...
à la présentation dans le catalogue ne sont pas mentionnées DIN 43763 et ⁄ ou suivant les standards spécifiques de Sauter ! explicitement et sont possibles suite au progrès technique et à l’amélioration Consignes pour le raccordement au process des sondes à...
EGT301F902 Rev. 2021 - V15 Termometro a resistenza per parete esterna con uscita passiva, 1x comando a due conduttori involucro in plastica antiurto e viti a chiusura rapida. Per il rilevamento della temperatura esterna o della temperatura negli ambienti umidi, per es.
Informazioni generali Informazioni generali sul montaggio delle sonde di temperatura: Le sonde si differenziano per struttura nei seguenti modi: sonde di temperatura a contatto, sonde di temperatura con cavo, sonde di temperatura con involucro e ad immersione. – Nelle sonde di temperatura a contatto, la sonda di temperatura possiede almeno una superficie di contatto che, ad es., viene appoggiata alla superficie del tubo o ai termosifoni.
DIN 43763 o degli montaggio. Eventuali versioni diverse rispetto alle immagini del catalogo non standard speciali Sauter! vengono descritte separatamente a posteriori e sono la conseguenza del progresso tecnico e del costante processo di miglioramento dei nostri Avvisi sul processo di collegamento delle sonde ad immersione prodotti.