Comet Spa CPS 29EH Bedienungsanleitung Seite 9

AFTER WORK
- After disconnecting the plug from the mains socket,
wind the lead around the hooks provided (fig.2) and
move the machine's handle to the vertical position,
until the pedal catch is heard.
- Empty both the tanks and rinse and dry them care-
fully.
- Return the tanks to the handle and place the ma-
chine in a protected place, where it is not at risk of
knocks, frost, humidity or water. The machine must
be placed on the stand provided to avoid damaging
the squeegee blades (fig. 1 0).
CLEANING THE BRUSH
- With the aid of a screwdriver, unscrew the 2 screws
shown in fig. 1 1.
- Free the brush by taking hold of it from the side of
the 2 screws just removed and extract if from the pin
on the opposite side
- Clean the brush under running water, taking care to
dry it perfectly before putting it back in place.
- To reconnect the brush, turn the drive pin to the po-
sition shown in fig. 1 2.
- Place the brush on the drive pin.
- Bring the bearing towards its seat.
- Turn the brush by hand while free to position the
bearing correctly.
- Re-close by tightening the 2 screws, taking care not
to trap the bristles of the brush.
CLEANING THE SQUEEGEE BLADES
- To remove the squeegee blades, they must be sepa-
rated by releasing the retainers at the ends (fig. 1 3)
and extracting them in opposite directions (fig. 1 4)
- Clean them under running water with the aid of a
non-aggressive detergent and insert them in the
guides, remembering to re-engage the end retain-
ers.
TROUBLESHOOTING
THE BRUSH DOES NOT TURN
- Check that the plug is connected to the mains sock-
et.
- Check that the switch is pressed correctly..
- If you are using a power lead extension, make sure
that it complies with the minimum dimensions stat-
ed in the safety precautions section.
- The brush motor has accidentally overheated: check
that the air intakes in the base have not become
blocked and wait for the overload cutout to reset.
- Check that there are no jammed objects preventing
the brush from rotation
- If the problem persists contact the nearest Service
Centre
THE MACHINE DOES NOT DELIVER DETERGENT
- Check that there is detergent in the tank
- The tank has not been fitted correctly and the deliv-
ery valve is not working. Reposition the tank.
- After removing the brush, clean the 4 detergent de-
livery nozzles with the pin provided (fig. 1 5)
- If the problem persists contact the nearest Service
Centre
THE MACHINE DOES NOT DRY
- Check that the suction squeegee blades are properly
positioned and that their end retainers are closed
(see maintenance section) (fig. 1 3).
- Empty the dirty detergent collection tank.
- Check that the hoses are connected (figs. 1 6 and 17)
and not bent at an acute angle (fig. 1 8).
- Check the wear of the pattern on the squeegee
blades (fig. 1 9). If necessary replace them, referring to
the maintenance section.
- Check the wear of the pattern on the squeegee
blades (fig. 1 9). If necessary replace them, referring to
the maintenance section.
- If the problem persists contact the nearest Service
Centre
THE MACHINE DOES NOT CLEAN PROPERLY
- Check that the brush and the squeegee blades have
been fixed correctly (see maintenance section).
- Check the brush for wear (the min. bristle length is
20mm). If necessary replace them, referring to the
maintenance section.
- If the problem persists contact the nearest Service
Centre
EXCESSIVE FOAM PRODUCTION
- Too much detergent in the water.
- If the problem persists contact the nearest Service
Centre
THE DETERGENT SOLUTION IS NOT EVENLY DISTRIBUTED
- After removing the brush, clean the 4 detergent de-
livery nozzles with the pin provided (fig. 1 5)
- If the problem persists contact the nearest Service
Centre
THE MACHINE LEAKS WATER
- Empty the dirty detergent collection tank (fig.8).
- Check that the O-ring seal is present and undam-
aged (fig.20)
- If the problem persists contact the nearest Service
Centre
WARRANTY
All our appliances have undergone thorough checks and are
covered by a 12-month warranty against manufacturing de-
fects. The warranty period starts from the date of purchase.
If the machine is repaired during the warranty period, a copy
of the purchase document must be enclosed.
The warranty is only valid if:
- The defects are of material or manufacturing (defects
which cannot be clearly attributed to the material or
manufacture will be examined by one of our techni-
cal service centres or on our premises, and the charg-
es will be allocated depending on the results).
- The instructions in this manual have been followed
to the letter.
- The repairs have been carried out by authorised re-
pairers.
- The machine has not been subjected to overloads
such as knocks, dropping or frost.
- Suitable detergents have always been used.
The warranty does not cover:
- Parts subject to normal wear and tear (brush, squee-
gee blades, paintwork).
- Accidental damage, damage during transport, dam-
age due to negligence or improper treatment, or
damage due to use or maintenance not in accord-
ance with the instructions provided in the this in-
struction manual.
- The cleaning of functional parts.
A repair under warranty includes the replacement
of faulty parts, while shipment and packaging are not in-
cluded. Any replacement of the appliance and extension of
the warranty further to work done on defects is not possible.
The repair is carried out at one of our authorised technical
service centres or on our premises and the machine must
reach us freight prepaid, i.e. with freight costs paid by the
user. The manufacturer declines any liability for any injury
or damage caused by poor installation or imperfect use of
the appliance.
DISPOSAL
As the owner of electrical or electronic
equipment, the law (in accordance with the
EU Directive 2012/19/EU on waste from
electrical and electronic equipment and the
national laws of the EU Member States that have
implemented this Directive) prohibits you from
disposing of this product or its electrical / electronic
accessories as municipal solid waste and obliges
you to make use of the appropriate waste collection
facilities.The product can be disposed of by
returning it to the distributor when a new product
is purchased. The new product must be equivalent
to that being disposed of. Disposing of the product
in the environment can cause great harm to the
environment itself and human health.
The symbol in the figure indicates the urban waste contain-
ers and it is strictly prohibited to dispose of the equipment
in these containers. Non-compliance with the regulationtis
spulated in the Directive 2012/19/EU and the decrees imple-
mented in the various EU Member States is administratively
punishable.
EN
9