Supra TURBO 654 Installations- Und Bedienungshandbuch Seite 13

WOODEN BEAM
No part of the wooden beam (C) should be subjected to heat from
the insert. Use the beam protection kit (D) available from your
dealer (Fig. 3.1.A) with insulation (A); rock wool; brick facing (E);
hood (B).
ELECTRICAL CONNECTION
Only the high-temperature resistant electrical cable supplied must
be used inside the fireplace.
ATTENTION: Lay the cable in a loop inside the
fireplace and make sure the loop is not trapped
underneath the appliance.
Pass the power cable through the hole made in the
fireplace. Connect the power cable to the mains
supply (230 V), respecting the polarities (phase,
neutral and earth (yellow/green)). The electrical
circuit is be protected by its own fuse inside the
insert.
Sleeve
Clips
Clamp
Loop
Side hatch
4. USE
ATTENTION:
If a niche under the fireplace is being used as firewood storage,
never block it completely (a front opening with a section of at
least 600 cm² must remain free at all times).
Leave a space of at least 5 cm between the bottom of the
fireplace and the top of the logs.
To avoid any risk of burns, do not touch the appliance and use
the cool hand key to operate the controls.
Heat emitted through the vitro ceramic glass makes it necessary
to keep any material that could be damaged by heat (furniture,
wallpaper, carpentry, etc.) away from the hearth. A distance of 2
m will avoid any risk.
High-temperature
resistant connection
cable
Side
hatch
Power cable
Mains connection
FUEL
Wood
This high-performance appliance requires quality fuel. Only burn
air-dried logs (2 to 3 years, stored in a sheltered and well-
ventilated place) with a maximum moisture content of 15 to 20%.
Preferably hard hardwoods (birch, hornbeam, beech ...),
Avoid soft hardwoods (linden, chestnut, willow, poplar),
Continuous use of resinous wood (pine, fir, etc.) as well as treated
wood (railway sleepers, carpentry offcuts, etc.) and household
waste (vegetable or plastic) is absolutely prohibited.
Never use small pieces of wood, boxes, woodchips or vine shoots
as these lead to sudden overheating.
ATTENTION:
The use of coal or coal derivatives, even
occasionally, is strictly prohibited. This appliance must not
be used to burn domestic waste.
DRAUGHT
Use of controlled mechanical ventilation (CMV) may influence the
draught, even reversing it. If the appliance is equipped with CMV,
then an open fresh-air intake is essential when the fireplace is
being used.
CONTROL DEVICES
Combustion air regulator
Use the damper on the ash box door to regulate the combustion
air (use the cold hand key).
Door handle
Use the cold hand key to handle the hearth door.
LIGHTING FOR THE FIRST TIME
Remove the self-adhesive labels, any possible blocking cards, and
make sure that the ash box is empty. It will take at least 2 weeks
for the chimney to start to operate normally.
- To light the fire from above, place 2 split logs in the hearth and
criss-cross a layer of kindling on top of the logs. Place a firelighter
on top of the wood and light it.
- To light it quickly from below, put down some crumpled paper,
then kindling on top and small pieces of wood on top of the
kindling.
Set the controls to the Light position (Table *). Light the fuel, close
the door and wait for embers to form. Once the fire is lit, load in
some wood and set the controls to the «nominal output» position,
Table (*). Lay the logs (at least 2 logs at the same time) towards
the back of the fireplace. It is best to load in the wood several
times rather than all at once.
If the outside temperature is very low, a heat «plug» may form
inside the flue, which is why it should be heated up gradually until
it reaches the normal draught rate.
OPERATION
Light
When lighting your appliance, it is best to use the lighting from
above method. This lighting technique allows the flue pipe to heat
up and eliminating any heat plugs (draught) that may form with
cold or inclement weather, preventing a backflow into the room
while the fire is getting started.
Proceed as follows:
- Put the air combustion control to the maximum setting.
- Place 2 logs on the hearth grate.
- Pile some kindling wood on top of the logs.
- Place 1 or 2 firelighters on top of the kindling and light them.
- Close the door.
For further information, view the Supra video on YouTube at:
https://www.youtube.com/watch?v=ebOr4vMj2Jo
ATTENTION: Never use petrol, alcohol or fuel oil ...