Inhaltsverzeichnis
Werbung
OBJ_BUCH-1845-003.book Page 16 Tuesday, March 17, 2015 9:53 AM
16 | English
Switching On and Off
To start the machine, press the On/Off switch 4 and keep it
pressed.
To lock the pressed On/Off switch 4, push the On/Off switch
4 further toward the front.
To switch off the power tool, release the On/Off switch 4, or
when it is locked, briefly press the On/Off switch 4 and then
release it.
To save energy, only switch the power tool on when using it.
Preselecting the Speed
Operate with a speed adapted to the application, in or-
der to prevent damage to the material.
The required speed can be preselected with the thumbwheel
3 (also while running).
The required speed depends on the material and the working
conditions and can be determined through practical testing.
When using fleece, do not work with a higher setting
than speed stage 4 (max.). Otherwise, the fleece will
become too hot.
Working Advice
When sanding, the removal capacity and the surface quality
are mainly determined by the abrasive selection as well as
through the preselected speed.
Work with the lowest possible sanding pressure in order to in-
crease the service life of the abrasive. Excessively increasing
the sanding pressure does not lead to a higher sanding capac-
ity, but to more wear of the power tool and the abrasive.
Work with moderate feed and perform the sanding parallel
and overlapping with respect to the sanding paths.
To achieve a perfect surface, do not skip more than one grain
size when selecting the abrasive.
Use only original Bosch sanding accessories.
Only proper abrasives achieve good sanding capacity and
give the power tool longer service life.
Do not clamp power tools in the saw stand. Clamped
power tools and sharp-edged application tools may result
in serious injury.
Storage of the Sanding Belts
Store sanding belts in their original packaging at
15 °C – 25 °C room temperature and 40 % – 70 % humidity.
Do not store sanding belts on concrete floors, close to open
windows or heaters.
Do not bend or kink the sanding belts, otherwise they will be-
come unusable.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
1 609 92A 180 | (17.3.15)
Remove adherent sanding dust with a brush.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Bosch Power Tools
Werbung
Inhaltsverzeichnis
