Inhaltsverzeichnis
Werbung
OBJ_BUCH-1845-003.book Page 14 Tuesday, March 17, 2015 9:53 AM
14 | English
Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent kickback
and loss of control.
Safety warnings specific for sanding operations
Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when select-
ing sanding paper. Larger sanding paper extending be-
yond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc, or kickback.
Additional safety warnings
Wear safety goggles.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled. This pre-
vents uncontrolled restarting.
Always operate the power tool with an application tool
mounted. Operation without an application tool is danger-
ous and can lead to injuries.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
1 609 92A 180 | (17.3.15)
Intended Use
The power tool is intended for dry sanding, structuring, satin-
finishing and matt-finishing of metal surfaces.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Spindle lock
2 Screw for clamping the dust cover
3 Thumbwheel for speed preselection
4 On/Off switch
5 Auxiliary handle (insulated gripping surface)
6 Dust cover
7 Feather key
8 Locking screw
9 Tool bit*
10 Spindle extension
11 Guide roller
12 Wing nuts
13 Handle (insulated gripping surface)
14 Hex key
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Satin-Finisher
Article number
Rated power input
No-load speed
Rated speed
Max. outer diameter of applica-
tion tool
Max. width of application tool
Mounting hole diameter
Speed preselection
Soft start
Constant electronic control
Restarting Protection
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 89 dB(A); Sound power level
100 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
GSI 14 CE
3 601 HB1 0..
W
1400
-1
min
750 – 3000
-1
min
3000
mm
115
mm
100
mm
19
kg
3.4
/II
Bosch Power Tools
Werbung
Inhaltsverzeichnis
