Bosch GGS 18 V-LI Professional Originalbetriebsanleitung Seite 14

OBJ_BUCH-1461-003.book Page 14 Thursday, July 10, 2014 10:26 AM
14 | English
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-23.
Typically the A-weighted noise levels of the product are:
Sound pressure level 77 dB(A); Sound power level 88 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and Uncertainty K
h
determined according to EN 60745:
Surface grinding (with wheel diameter of 25 mm):
2 2
a =3.5 m/s , K=1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Technical Data
Straight grinder
Article number
Rated voltage
Rated speed
Collet chuck diameter, max.
Spanner size of
– clamping nut
– grinder spindle
Grinding tool diameter, max.
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
*
– during operation and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
1 609 92A 0MA | (10.7.14)
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-23.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 16.06.2014
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
GGS 18 V-LI
The lithium-ion battery is protected against deep discharging
3 601 JB5 3..
by the "Electronic Cell Protection (ECP)". When the battery is
V= 18
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
-1
min 22000
 Do not continue to press the On/Off switch after the
mm 8
machine has been automatically switched off. The bat-
tery can be damaged.
mm 19
Observe the notes for disposal.
mm 19
Removing the battery
mm 50
The battery 7 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
kg 1,8
unlocking button 6 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
°C 0...+45
spring.
°C –20...+50
GBA 18V ...
AL 18..
GAL3680
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools