Electrical Connection - Imer Group KOINE 4 Handbuch Fur Bedienung, Wartung

7. MECHANICAL SAFETY
The hazardous points on the IMER plastering machine are
protected by means of suitable safety devices, which must remain
¿WWHG DW DOO WLPHV DQG NHSW LQ SHUIHFW FRQGLWLRQ VXFK DV WKH HOHFWULF
motor cooling fan guard and the grille on the hopper to prevent
contact with the cell wheel.
Also opening of the mixing chamber, either via the motor support
ÀDQJH RU WKH FRPSOHWH PL[LQJ FKDPEHU VKXWV GRZQ WKH URWDU\ SDUWV
RI WKH PDFKLQH WKDQNV WR D VSHFL¿F VDIHW\ PLFURVZLWFK
8. TRANSPORT
- Caution! Before moving the plastering machine, always
detach the power plug.
Before moving the plastering machine the water delivery hose and
material delivery line must be removed.
Only a minimal amount of the material should be in the hopper
when handling.
Release the wheel by means of the brake and move the mixer by
PHDQV RI WKH KDQGOHV ¿J 
FIG.2
- Caution! Before lifting the plastering machine, always
disassemble the compressor for separate transport.
- Caution! Before lifting the machine, always check that
DOO PDFKLQH FRPSRQHQWV DUH FRUUHFWO\ VHFXUHG DQG ¿WWHG LQ
place.
7R OLIW WKH PDFKLQH XVH WKH VSHFL¿F DWWDFKPHQW ULQJV ¿J 
- Caution! Lift with care to avoid hazardous oscillations
 &DXWLRQ 1HYHU XVH SRLQWV RWKHU WKDQ DV VSHFL¿HG LQ
¿JXUH  WR OLIW WKH PDFKLQH DQG LQ SDUWLFXODU GR QRW KRRN XS
lifting equipment to the gearmotor guard.
Use lifting equipment suited to the overall weight of the machine
indicated in table 1.
To facilitate transport, the machine can be disassembled as
VKRZQ LQ ¿J
IMER INTERNATIONAL S.p.A.
KOINE 4/5
.
7KH ZHLJKW RI WKH VXEXQLWV VKRZQ LQ ¿J DUH VSHFL¿HG LQ WDEOH 
9. INSTALLATION
3RVLWLRQ WKH SODVWHULQJ PDFKLQH RQ D ÀDW VXUIDFH LQ DQ DUHD ZKHUH
it does not constitute an obstruction either during use or cleaning
at the end of the work shift and where a minimum quantity of
pipelines is required.
Secure the machine in place by means of the wheel brake (ref.5
¿J 
10. CONNECTIONS

10.1 ELECTRICAL CONNECTION

and electrical connection (socket, fuses, cable) correspond
WR VSHFL¿FDWLRQV LQ WDEOH 
7KH HOHFWULFDO SRZHU OLQH PXVW EH ¿WWHG ZLWK SURWHFWLRQ DJDLQVW
current overload (e.g. by means of fuses or a thermal magnetic
FXWRXW DQG ZLWK FXUUHQW GLVSHUVLRQ WR HDUWK HJ ZLWK D GL HUHQWLDO
circuit breaker). The electric cable wire size must take into account
the operating currents and length of the line to avoid excessive
voltage drops.
Avoid use of extension leads wound on drums. The power cable
must be suitable for frequent movements and with an abrasion
resistant sheath (e.g. type H07RN-F).
Before connecting the plastering machine to the electrical mains,
HQVXUH WKDW DOO VDIHW\ GHYLFHV DUH ¿WWHG DQG DUH LQ SHUIHFW FRQGL-
tion, and check in particular that the hopper grille is secured in
FIG.3
place, that the extension in good condition and that the plugs and
sockets are not wet.
Connect the plastering machine socket on the electrical panel to
WKH PDLQV ¿J 
21
FIG.4
- Ensure that the power supply voltage, mains frequency
FIG.5