Display Backlight - TFA 60.5017.01 Bedienungsanleitung

TFA_No. 60.5017_Anl_09_22
Radio-controlled projection alarm clock
• The sequence is shown as follows:
– TIME
– IN TEMP indoor temperature
– TIME/TEMP time/indoor temperature alternating
• Press the Projection HIGH/LOW/OFF button to adjust the projection brightness in 2
levels or to switch it off.
• If the projection is switched on, the last selected display and the alarm symbol (if
the alarm is activated) appear on the wall or ceiling.
• Set the projection arm to the respective position.
• With the ROTATE dial you can rotate the image by 270°.
• Battery operation: To temporarily activate the projection, press the Projection
HIGH/LOW/OFF button.

8.2 Display backlight

• Press the SNOOZE/LIGHT button to adjust the brightness in 4 levels (BACKLIGHT 1-
4) or to switch it off (OFF).
• Wait some seconds until the display returns to normal mode to confirm the setting.
• Battery operation: To temporarily activate the backlight, press the SNOOZE/LIGHT
button.
8.2.1 Automatic dimming mode
• If the auto-dim mode is activated, the weak backlight (level 1) turns on automati-
cally for the set time. After that, the backlight goes to level 4.
• Press and hold the SNOOZE/LIGHT button for 2 seconds. AUTO DIM appears on the
display.
• By default, the automatic dimming function is disabled. OFF flashes on the display.
• To activate the function, press the + or – button (ON). The AUTO DIM symbol
appears on the display.
• Confirm with the SNOOZE/LIGHT button.
• The start time flashes (START TIME 22:00 default). Press the + or – button to set
the time (full hours).
• Confirm with the SNOOZE/LIGHT button.
• The end time flashes (STOP TIME 6:00 default). Press the + or – button to set the
time (full hours).
• Confirm the settings with the SNOOZE/LIGHT button. The display returns to normal
mode and the AUTO DIM symbol remains.
9. Battery replacement
• Change the batteries when the battery symbol appears on the display (optional).
21.09.2022 10:33 Uhr Seite 14
– 26 –
Radio-controlled projection alarm clock
10. Location and mounting
• Place the projection alarm clock at your chosen location.
• Avoid being close to possible sources of interference that may affect radio recep-
tion. It is recommended to keep a distance of at least 2 metres to possibly interfer-
ing sources (TV, computer, microwave, wireless phones, baby monitors) and large
metal objects (e.g. refrigerator). Within solid walls, especially ones with metal
parts, the transmission range can be reduced considerably. In extreme cases,
please place the unit close to a window to improve reception.
• Check whether the DCF radio clock signal can be received.
• If necessary, choose another position.
• Do not use the product in the vicinity of radiators, other sources of heat or in direct
sunlight.
11. Troubleshootingtigung
Problem Solution
➜ Control the power adapter
No display on the
projection alarm clock Battery operation
➜ Ensure the batteries' polarities are correct
➜ Change the batteries
No permanent projection ➜ Press Projection HIGH/LOW/OFF button
➜ Connect the device to the power adapter
No permanent backlight ➜ Press the SNOOZE/LIGHT button.
➜ Connect the device to the power adapter
➜ Activate (DCF ON) the DCF reception in setting mode.
No DCF reception
➜ Activate reception manually (press SET button briefly)
➜ Wait for an attempt reception during the night
➜ Change the location (interference!)
➜ Set the clock manually
➜ Restart the device
Incorrect indication
Battery operation
➜ Change the batteries
If your device fails to work despite these measures, please contact the retailer where
you purchased the product from for advice.
– 27 –