VOLTCRAFT BS-3.9/1m Bedienungsanleitung Seite 2

Operating Instructions
BS-3.9/1m QVGA Camera probe
Item No. 409211
Intended use
This product is a camera attachment for various endoscope main units from the Voltcraft
product range (see the compatibility list under "Technical data"). It is designed for visual
troubleshooting and inspection of voltage-free systems and installations. The flexible camera
neck permits the camera located on the tip to reach otherwise inaccessible positions. There are
two LEDs integrated in the camera head, permitting recording in dark spaces. The brightness of
the LEDs can be regulated via the connected endoscope main unit. The camera neck and head
are waterproof and thus suitable for use in voltage-free liquids (no acidic or basic solutions).
Use on persons or animals as well as in potentially explosive areas is not permitted. The device
is supplied with power via the connected endoscope main unit.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• QVGA camera probe
• Lens cap
• Operating instructions
Up-to-date operating instructions
Download the latest product information at
shown. Follow the instructions on the website.
Symbol explanation
The triangle containing a lightning symbol warns against danger of electric shock or
impairment of the electrical safety of the device.
The exclamation mark symbol indicates important parts of the operating instructions,
which are to be observed at all times.
The arrow symbol indicates special hints and operating information.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient condi
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Heed all legal regulations for operation of the product. Do not use the product for
the surveillance of persons!
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have any questions that are not answered in these operating instructions,
please contact our technical support centre or consult a professional.
www.conrad.com/downloads or scan the QR code
tions or
Operation
Hold the camera head and neck only in voltage-free liquids (no acidic or basic
solutions). The camera neck may not be submerged in water past the marking "IP
67 max. water level" located on the plug, as the plug itself is not waterproof.
The endoscope is suited for inspection only in voltage-free systems. The camera
head is made of metal and can cause short-circuiting. For safety reasons, make
sure all system components are voltage-free before inspection.
Do not exceed the minimum bending radius of 45 mm.
Place the included lens cap on the camera lens when the camera is no in use.
1. Carefully connect the product plug to the corresponding socket on your endoscope main
unit.
Make sure that the pins inside the plug are correctly aligned with the socket to
prevent their breaking off or bending.
2. Secure the connection using the fastening ring on the endoscope main unit.
3. Repeat these steps in reverse order to disconnect the product from your endoscope main
unit.
You can find further operating instructions, such as on regulation of LED brightness,
in the operating instructions of the endoscope main unit.
Maintenance and cleaning
• Before cleaning, disconnect the product from the endoscope main unit.
• Use a small brush or cotton swab to clean the camera lens.
• Use a cloth, slightly damp with lukewarm water, to clean the camera neck.
Disposal
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up
by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.
Technical data
Compatible with ............................ BS-200XW, BS-250XWSD, BS-220XIP, BS-300XRSD,
BS-50X, BS-100XIP, BS-250XIPSD, BS-350XIPSD
Resolution ..................................... 320 x 240
Lighting ......................................... 4 white LEDs
Illuminance ................................... max. 900 lux ±150 lux (at a distance of 20 mm)
Bending radius .............................. >45 mm
Protection type .............................. IP67
Field of view .................................. 54º
Focus ............................................ 10 – 50 mm
Operating conditions ..................... 0 to +45 ºC, 15 – 85 % RH
Storage conditions ........................ -10 to +50 ºC, 15 – 85 % RH
Camera head Ø ............................ 3.9 mm
Length........................................... 104 cm ±2 cm
Weight .......................................... approx. 50 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2022 by Conrad Electronic SE. *409211_v3_1022_02_dm_mh_en