Fluval SIENA 166 Gebrauchsanleitung Seite 6

FULL SETUP GUIDE
AQUARIUM CABINET INSTALLATION AND PREPARATION
Before handling the aquarium tank and cabinet, ensure you have su cient people to move them without any risk.
ASSEMBLE THE AQUARIUM CABINET BEFORE REMOVING THE AQUARIUM FROM ITS PACKAGING.
You MUST place the Fluval aquarium on the appropriate Fluval cabinet which was designed with the correct dimensions
and structure to bear the weight of the aquarium full of water. The use of di erent cabinets, pieces of furniture, TV stands, etc.,
WILL invalidate your warranty and will compromise the product safety.
Please refer to the instruction manual of the aquarium cabinet. Do not attempt to set up the cabinet without reading
and following the instruction manual. If it is missing or unusable, contact the store or Hagen Customer Service.
Placing the aquarium with its cabinet in the nal location
Location of the aquarium is very important. Place the aquarium away from direct sunlight. This will reduce the risk of excessive algae build-up and avoid overheating the
aquarium by the sunrays. Keep your Fluval Aquarium away from other sources of heat (air ducts, radiators, etc.) for proper temperature maintenance. Drafts should also be
avoided. Do not locate your Fluval Aquarium where water spills will cause damage.
WARNING: Ensure that the selected position has an even and level surface which is able to support the total weight of the aquarium
full of water and the cabinet. Place your new Fluval Aquarium and cabinet close to an electrical outlet. After placing the cabinet,
assure that it is perfectly level by using an adequate leveling tool.
IMPORTANT: Fluval cabinets are designed to support the total weight of the aquarium. The table below shows the approx. height
of lling of the tank and approx. weight of the aquarium full of water (rocks, decorations or gravel have not been considered).
FLUVAL SIENA AQUARIUMS
MODEL
FLUVAL SIENA 166
FLUVAL SIENA 272
FLUVAL SIENA 332
THE AQUARIUM INSTALLATION
Before handling the aquarium tank and cabinet, ensure you have su cient people to move them without any risk.
TAKE THE AQUARIUM TANK OUT FROM ITS PACKAGING
The aquarium glass tank comes with runners glued to it to support the LED Strip Lights and covers.
Do not try to remove the runners.
The tank is made of glass, always handle it with the utmost care. Make sure to lift it only by the base.
PLACE THE AQUARIUM TANK ONTO THE CABINET
IMPORTANT: Thoroughly clean the top side of the cabinet base and the lower side of the aquarium base.
Place the empty aquarium tank onto the cabinet, making sure that the connections
lie in the appropriate opening of the cabinet. NEVER place anything underneath
the aquarium. There should be NO additional support or lining (e.g., polystyrene mats)
between the aquarium and the cabinet.
WARNING: Risk of breaking the glass tank base.
The glass tank features protruding ttings at the bottom, which can never be used
as support points. Never try to lay the tank on any support except its cabinet, which
is tted with a special cavity to accommodate the ttings. When placing the tank
onto its cabinet, remove the tank from the box and rest it on the cabinet paying
the utmost attention not to damage the bottom ttings.
6
External
Tank Dimensions
55 x 55 x 55 cm
21.5 x 21.5 x 21.5''
90 x 55 x 55 cm
35.5 x 21.5 x 21.5''
110 x 55 x 55 cm
43.5 x 21.5 x 21.5''
Height of Filling
(Up to the max water level line)
49.5 cm / 19.5"
(Water capacity= 140 L / 37 US Gal)
49.5 cm / 19.5''
(Water capacity= 227 L / 60 US Gal)
49.5 cm / 19.5''
(Water capacity= 279 L / 74 US Gal)
Weight of aquarium
lled only with water
166 kg / 366 lb
277 kg / 611 lb
340 kg / 750 lb