Safety Instruction - HIKMICRO G Serie Kurzanleitung

Safety Instruction

These instructions are intended to ensure that user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
● Use of the product must be in strict compliance with
the local electrical safety regulations.
Transportation
● Keep the device in original or similar packaging while
transporting it.
● Keep all wrappers after unpacking them for future use.
In case of any failure occurred, you need to return the
device to the factory with the original wrapper.
Transportation without the original wrapper may result
in damage on the device and the company shall not
take any responsibilities.
● Do not drop the product or subject it to physical shock.
Keep the device away from magnetic interference.
Power Supply
● The input voltage should meet the Limited Power
Source (5 VDC, 940 mA ) according to the IEC61010-1
standard. Please refer to technical specifications for
detailed information.
● Make sure the plug is properly connected to the power
socket.
● DO NOT connect multiple devices to one power
adapter, to avoid over-heating or fire hazards caused
by overload.
Battery
● The built-in battery cannot be dismantled. Please
contact the manufacture for repair if necessary.
● DO NOT charge other battery types with the supplied
charger. Confirm there is no flammable material within
2 m of the charger during charging.
● For long-term storage of the battery, make sure it is
fully charged every half year to ensure the battery
quality. Otherwise, damage may occur.
● DO NOT place the battery near heating or fire source.
Avoid direct sunlight.
● DO NOT swallow the battery to avoid chemical burns.
● DO NOT place the battery in the reach of children.
● When the device is powered off and the RTC battery is
full, the time settings can be kept
for 15 days.
● In the first use, power on the device and charge the
RTC battery with the lithium battery for more than 10
hours.
● The battery voltage is 3.6 V, and the battery capacity is
6700 mAh.
● The battery is certified by UL2054.
● CAUTION: Risk of explosion if the battery is replaced by
an incorrect type.
Maintenance
● If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
● A few device components (e.g., electrolytic capacitor)
require regular replacement. The average lifespan
varies, so periodic checking is recommended. Contact
your dealer for details.
● Wipe the device gently with a clean cloth and a small
quantity of ethanol, if necessary.
● If the equipment is used in a manner not specified by
the manufacturer, the protection provided by the
device may be impaired.
● We recommend you send the device back for
calibration once a year, and please contact the local
dealer for the information on maintenance points.
● Please notice that the current limit of USB 3.0
PowerShare port may vary with the PC brand, which is
likely to result in incompatibility issue. Therefore it's
advised to use regular USB 3.0 or USB 2.0 port if the
USB device fails to be recognized by PC via USB 3.0
PowerShare port.
● Your camera will periodically perform a self-calibration
to optimize image quality and measurement accuracy.
In this process the image will pause briefly and you'll
hear a "click" as a shutter moves in front of the
detector. The self-calibration will be more frequent
during start up or in very cold or hot environments.
This is a normal part of operation to ensure optimum
performance for your camera.
Using Environment
● DO NOT expose the device to extremely hot, cold,
dusty, corrosive, saline-alkali, or damp environments.
Make sure the running environment meets the
requirement of the device. The operating temperature
shall be -20 °C to 50 °C (-4 °F to 122 °F), and the
operating humidity shall be 90% or less.
● This device can only be safely used in the region below
2000 meters above the sea level.
● Place the device in a dry and well-ventilated
environment.
● DO NOT expose the device to high electromagnetic
radiation or dusty environments.
● DO NOT aim the lens at the sun or any other bright
light.
● When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may
burn out.
● The device is suitable for indoor and outdoor uses, but
do not expose it in wet conditions.
● The level of protection is IP 54.
● The pollution degree is 2.
Technical Support
● The https://www.hikmicrotech.com portal will help
you as a HIKMICRO customer to get the most out of
your HIKMICRO products. The portal gives you access
to our support team, software and documentation,
service contacts, etc.
Emergency
● If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Laser
Warning: The laser radiation emitted
from the device can cause eye injuries,
burning of skin or inflammable
substances. Prevent eyes from direct
laser. Before enabling the Light Supplement function,
make sure no human or inflammable substances are in
front of the laser lens. The wave length is 650 nm, and the
power is less than 1 mW. The laser meets the
IEC60825-1:2014 standard.
Laser maintenance: It is not necessary to maintain the
laser regularly. If the laser does not work, the laser
assembly needs to be replaced in the factory under
warranty. Keep the device power off when replacing laser
assembly. Caution-Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing
Subdistrict, Binjiang District, Hangzhou, Zhejiang 310052,
China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products might
be subject to export controls in various countries or
regions, including without limitation, the United States,
European Union, United Kingdom and/or other member
countries of the Wassenaar Arrangement. Please consult
your professional legal or compliance expert or local
government authorities for any necessary export license
requirements if you intend to transfer, export, re-export
the thermal series products between different countries.
6