Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Cutting-means Mounting Bolt Inspection
Inspect the cutting-means bolts for any signs of
damage or looseness. If they are damaged, they
must be replaced.
If they appear loose, a torque wrench must be
used to accurately tighten the cutting-means bolts
to the required torque. If you do not have a torque
wrench, take your lawnmower to an authorized
dealer to have the bolts replaced or tightened.
Use only Honda Genuine cutting-means bolts and
special washers, since they are specifically
designed for this purpose. Replacement part numbers are on page 17.
Cutting-means Replacement
CAUTION:
• Cutting-means balance is critical to proper lawnmower performance.
Replace any cutting means that is damaged or out of balance.
• Use only genuine Honda replacement cutting means.
Cutting-means Sharpening
CAUTION:
• To avoid weakening the cutting means, causing it to become unbalanced or
getting a bad quality of cut, the cutting means should be sharpened by
competent personnel at your servicing dealer.
1. Sharpen the cutting means cutting edges with a file. File the top side
only. Maintain the original bevel for a fine cutting edge. File both ends
evenly to maintain cutting-means balance.
2. After sharpening, test the cutting-means balance using a screwdriver
as shown above. If either side dips slightly below the horizontal, file
that side. Replace the cutting means if it dips excessively.
15 mm
Max.
GRASS CATCHER CLEANING AND
REPLACEMENT
Cleaning
Wash the grass catcher with a garden hose, and allow it to dry completely
before use; a wet grass catcher will clog quickly.
Replacement
Replace a worn or damaged grass catcher with a Honda replacement part
or its equivalent.
14 EN
OPERATION CHECK OF THE CUTTING-MEANS
Inspect washers and
CONTROL
bolt heads for
looseness and
VKEA Type only:
damage.
Start the engine outdoors. Release the cutting-means control lever; the
engine should stop quickly. If the engine does not stop quickly, take the
mower to an authorized Honda servicing dealer for repair.
MAINTENANCE SCHEDULE
Perform at every indicated month/year or operating hour interval,
whichever comes first.
Item
Engine oil
Air filter
Spark plug
Spark arrester
(if equipped)
Fuel tank
Valve
clearance
Fuel lines
Grass catcher
Cutting-means Check
Operation of the
cutting-means
control
Rear shield
Cutting-means
bolts
Smart Drive
cable
Roto-Stop
cable (VYEA)
Throttle cable
(VYEA)
7 mm
Pinion gears
Max.
Transmission
axle bearings
1. Service more frequently when used in dusty areas.
2. These items should be serviced by an authorized Honda servicing
dealer, unless you have the proper tools and are mechanically
proficient. Refer to the Honda shop manual for service procedures.
3. In Europe and other countries where machinery directive 2006/42/EC is
enforced, this cleaning should be done by your servicing dealer.
Failure to follow this maintenance schedule could result in
non-warrantable failures or reduction in performance and emissions
C12
D6
SAFETY
noncompliance.
Before
each
use
Intervention
Check
o
Change
Check
o
Clean
Replace
Check / Adjust
Replace
3
Clean
2
Clean
Adjust
2
Check (replace
2
if necessary)
Check
o
o
Check
o
Check
o
Check
o
Adjust
2
Adjust
2
Adjust
2
2
Grease
Check
2
Frequency
Every
First
Every
6
month
First 25
year
months
or 5
hours
or 100
or 50
hours
hours
hours
1
1
o
o
o
1
1
1
o
o
o
o
o
o
o
Every 2 years
o
o
o
o
o
o
o
o
o
Every 2
years or
150
running
hours
1
o
o
o
o
o
o
o
o
o
o
o
o
Werbung
Inhaltsverzeichnis
Fehlerbehebung
