Technical Data - Milwaukee M18 FBTS75 Originalbetriebsanleitung

TECHNICAL DATA

Type
Production code
Battery voltage
Belt speed no load
Sanding width
Belt length
Dimensions of grinding plate
Weight according EPTA-Procedure 01/2014
(Li-Ion 2,0 Ah ... 12,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Noise information Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
Vibration information Vibration total values (triaxial vector sum) determined
according to EN 62841
Vibration emission value a / Uncertainty K
h
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING!
Read all safety warnings, instructions,
illustrations and specifications provided with this power tool. Failure
to follow all instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR SANDERS
Collected sanding dust from sanding surface coatings such as
polyurethanes, linseed oil, etc. can self-ignite in the sander dust bag
or elsewhere and cause fire. To reduce the risk of fire always empty
the dust bag frequently (10-15 minutes) while sanding and never
store or leave a sander without totally emptying its dust bag. Also
follow the recommendations of the coatings manufacturers.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Never reach into the danger area of the machine when it is running.
Chips and splinters must not be removed while the machine is
running.
Use protective equipment. Always wear safety glasses when
working with the machine.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in order
to find out the cause.
The workpiece must be fixed if it is not heavy enough to be steady.
Do not let any metal parts enter the airing slots - danger of short
circuit!
Do not machine any materials that present a danger to health (e.g.
asbestos).
When grinding metal, flying sparks are produced. Take care that
no persons are endangered. Because of the danger of fire, no
16
M18 FBTS75
Belt Sander
4912 50 01 XXXXXX MJJJJ
18 V ⎓
210 - 410 m/min
75 mm
457 mm
90 x 135 mm
3,9 ... 5,0 kg
-18 ... +50 °C
M18B...; M18HB...
M12-18...; M1418C6
89,98 dB (A) / 3 dB (A)
100,98 dB (A) / 3 dB (A)
1,47 m/s 2 / 1,5 m/s
combustible materials should be located in the vicinity (spark flight
zone). Do not use dust extraction.
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them. Corrosive or
conductive fluids, such as seawater, certain industrial chemicals,
and bleach or bleach containing products, etc., Can cause a short
circuit.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
SPECIFIED CONDITIONS OF USE
The belt sander can be used for sanding wood, plastic, metal, filler
and painted surfaces.
This machine is suitable only for dry sanding.
Do not use the product in any way other than those stated for
intended use.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Injury caused by vibration. Hold the product by designated
handles and restrict working time and exposure.
• Exposure to noise can cause hearing injury. Wear ear protection
and limit exposure.
• Injury due to flying debris. Wear eye protection, heavy long
trousers, gloves and substancial footwear at all times.
• Inhalation of toxic dusts.
ENGLISH
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will vibrate for about 5
seconds, the fuel gauge will flash,and then the tool will turn OFF.
To reset, release the trigger. Under extreme circumstances, the
2
internal temperature of the battery pack could raise too much. If
this happens, the fuel gauge will flash until the battery pack cooled
down. After the lights go off, the work may continue.
Transporting Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
Ensure that battery pack is secured against movement within
packaging. Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
WORKING INSTRUCTIONS
The stock removal rate during sanding and the surface finish
are essentially determined by the choice of sanding belt and the
preselected belt speed. The higher the belt speed, the higher the
stock removal and the finer the sanding surface.
Only flawless abrasive belts produce good sanding performance and
protect the power tool. If possible, work with a low contact pressure
to increase the service life of the sanding belts. The dead weight of
the power tool is sufficient for good sanding performance. Excessive
increase of the contact pressure does not result in higher sanding
performance, but in greater wear of the power tool and the sanding
belt.
Place the power tool switched on on the surface to be machined.
Work at a moderate feed rate and carry out the sanding process
parallel and overlapping to the sanding paths. Sand in the direction
of the grain, crosswise sanding tracks result in disturbing sanding
effects.
Particularly when sanding off paint residues, these may melt and
smear the material surface and the sanding belt. Therefore, work
with dust extraction.
A sanding belt with which metal has already been processed should
not be used for other materials.
Only store abrasive belts in a hanging position and do not bend
them, otherwise they will become unusable.
Self-suction with dust bag
For smaller jobs you can connect a dust bag.
External suction
Connect the suction hose to a vacuum cleaner. Use a special
vacuum cleaner when extracting dust that is particularly hazardous
to health, carcinogenic or dry dusts.
Preselect belt speed
The required belt speed depends on the material and the working
conditions and can be determined using practical tests.
CLEANING
The ventilation slots of the machine must be kept clear at all times.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
ENGLISH
17