Technical Data; Angle Grinder Safety Warnings - Milwaukee M18 FSAG115X Originalbetriebsanleitung

18

TECHNICAL DATA

Type
Production code
Battery voltage
Rated speed
Thread of work spindle
D=Grinding disc diameter max.
d=Grinding disc hole diameter
b=Grinding disc thickness max.
b=Cutting disc thickness max. / min.
D=Sanding disc diameter max.
D=Wiring brush diameter max.
Weight according EPTA-Procedure 01/2014
(Li-Ion 2,0 Ah ... 12,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
< 30°
Recommended charger
Noise information: Measured values determined according to
EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
Vibration information: Vibration total values (triaxial vector sum)
determined according to EN 60745.
Vibration emission value a / Uncertainty K
h
Surface grinding
Disc sanding
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire Brus-
hing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder, sander,
wire brush or cut-off tool. Read all safety warnings, inst-
ructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
b) Operations such as polishing are not recommended to be
performed with this power tool. Operations for which the power
tool was not designed may create a hazard and cause personal
injury.
M18 FSAG115X M18 FSAG125X
Cordless Angle Grinder Cordless Angle Grinder
4830 49 01 XXXXXX MJJJJ 4830 56 01 XXXXXX MJJJJ
18 V
8500 min 8500 min
-1
M14
115 mm
22,2 mm
6 mm
3 mm / 1 mm 3 mm / 1 mm
115 mm
75 mm
2,4 ... 3,4 kg 2,4 ... 3,5 kg
-18 ... +50 °C
M18B...; M18HB...
M12-18...; M1418C6
82,7 dB(A) / 3 dB(A) 82,7 dB(A) / 3 dB(A)
93,7 dB(A) / 3 dB(A) 93,7 dB(A) / 3 dB(A)
4,8 m/s / 1,5 m/s 5,5 m/s
2 2
1,1 m/s / 1,5 m/s 1,9 m/s
2 2
c) Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure
safe operation.
d) The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
f) Threaded mounting of accessories must match the grinder
spindle thread. For accessories mounted by flanges, the
arbour hole of the accessory must fit the locating diameter of
the flange. Accessories that do not match the mounting hardware
of the power tool will run out of balance, vibrate excessively and
may cause loss of control.
ENGLISH
18 V
-1
M14
125 mm
22,2
6 mm
125 mm
75 mm
/ 1,5 m/s
2 2
/ 1,5 m/s
2 2
19