Dust Extraction; Warranty; Maintenance And Care - Felisatti SCF 190/1600 Bedienungsanleitung

on the fixed guard of the machine indicates the cutting
direction of the teeth).
SETTINGS
1. Cutting depth setting
For a clean perfect cut, the cutting depth should be adjusted
to the thickness of the wood to be worked on, so that the saw
blade protrudes a tooth's height from the material.
To adjust the cutting depth, loosen the wing nut G and move
the machine upwards or downwards. The scale printed on
the parallel guide indicates the cutting depth.
. Cutting angle setting
It can cut vertically and with an inclination of up to º. The
angle is adjusted by loosening the wing nut M and according
the scale printed on the base.
. Riving knife adjustment
WARNING: The riving knife F prevents the blade from seizing
up duriing cutting operations and shold alwyas be used for
safety reasons.
The machine is supplied with the riving knife adjusted. When
fitting a new blade, follow the steps below for readjustment:
1. Raise the mobile guard C and loosen rhe screw button
B.
. Move the wedge through the slot to a distance from the
teeth tip and a cutting depth from same of  to  mm (máx. 
mm).
. Tighten the screw B and the machine is ready to work.
. Lateral stop adjustment
For parallel cutting, use the lateral stop I.
Cutting width is adjusted with the scale or according to the
plotting.
Tighten the wing nut H to work with the lateral stop.

DUST EXTRACTION

WARNING! Always make sure that the tool is switched off
and unplugged before fitting or removing any dust extraction
device.
Dust extraction keeps the workplace clean, prevents dust
build-up in the air and facilitates waste elimination.
These saws are equipped with a dust extraction hole N
to which an adapter can be fitted (suppied as an optional
accessory).
A universal vacuum cleaner may be fitted or any dust
extraction device.
CAUTION: Always use a vacuum extractor designed in
accordance with the applicable Guidelines on sawdust
emission. The flexible hoses of conventional vacuum
cleaners fit directly onto the dust extraction nozzle.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.

MAINTENANCE AND CARE

WARNING! Always unplug the machine before carrying out
work on it.
- Checking the saw blade: Deposits of resin and glue on
the saw blade cause inefficient cutting. To avoid them, always
clean the blade immediately after use.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tightened.
Should any screw be loose, tighten it immediately. Failure to
do so could put you at serious risk.
6
- Motor maintenance: Always take the greatest care over
this and make sure that the motor winding is not damaged
and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is not,
take it to an Official Service Centre to have it replaced.
- Brush replacement: Brushes must be replaced when
length reaches 8 mm or less. To do so, please contact an
authorized after sales service center. We recommend that
every other time you take a tool to an after sales service
center for carbon brushes replacement you also order a
general maintenance (cleaning and lubrication).
Use only Felisatti accessories and spares. Parts the changing
of which is not covered in this instruction manual, should be
replaced in a Felisatti Official Service Centre (See Warranty/
Official Service Centre address leaflet).

WARRANTY

See general warranty conditions printed on the attached
sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise to a
minimum. However, in spite of this, in certain circumstances
the maximum noise level in the place of work could exceed 8
dBA. In this case, the operator should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN 01, usually reach:
Acoustic pressure = 96 dB(A)
Sound-power level = 109 dB(A)
Use ear protection!
Vibration acceleration = .7 m/s