Starting Up The Machine; Floor Milling - Schwamborn BEF 320EX Originalbetriebsanleitung

EN Floor milling machine BEF 320EX / BEF 320VX
3 Operation

3.1 Starting up the machine

Observe the safety instructions in Chapter 2.
The machine may only be started up by
qualified personnel.
A visual inspection of the machine must be car­
ried out before starting up the machine.
Particular attention should be paid to damaged
or loose components, and wear.
BEF 320VX:
Suffocation and poisoning hazard from toxic
exhausts!
Machines with combustion engines may not be
operated in closed
depressions without sufficient supply of fresh air.
Check fuel levels of petrol and oil.
(! HONDA operating manual).
The machine is delivered with an oil filling
but not with petrol.
4. BEF 320VX:
Turn the fuel valve [30, Fig. E]and the motor
switch [32, Fig. E] to
(! HONDA operating manual).
BEF 320EX:
Disconnect the mains [26, Fig. D].s
The drive motor and the milling rotor are at a
standstill.
5. Check the the functioning and condition of the
milling rotor and milling discs and replace if nec­
essary (! Chapter 4.2 ‐ page 22).
6. Remove any protruding objects from the surface
to be milled.
7. Attach external dust extraction at the connection
to the dust extraction [21, Fig. G].
Dust extraction is provided by the customer.
The suction hose can be attached with Velcro
strips to the cross bar [2] and on the safety
bar [1] (Fig. G).
8. Check the dust protection brushes [12, Fig. I] for
proper position and function and, if necessary,
correct.
9. If necessary, insert the safety peg [35, Fig. F] all
the way into the safety switch [34, Fig. F].
10. The operator should sling the safety
line [36, Fig. F] around their wrist so that if the
operator goes away from the guide handle, it is
assured that the safety peg will be separated
from the safety switch.
The machine is ready for operation.
rooms or in ground
OFF

3.2 Floor milling

Never use the machine on a floor tilt angle of
more than 10°!
The operator must always be able to control and
steer the machine!
The guide handle [5] may not be released during
operation. All operating elements must always
be within reach.
The machine is ready for operation.
(! Chapter 3.1 ‐ page 19).
1. Shift the drive lever [4, Fig. A] into the middle
position (f).
2. Pull the lift lever (quick lift) [16, Fig. C] all the way
back [19, Fig. C].
The lift lever latches into place.
The milling rotor is raised.
3. Press the transport pedal [14, Fig. B] all the way
down until it locks into place.
The 2 transport wheels [11, Fig. A/B] are pressed
down.
The machine can be lifted by the handles
[9, Fig. A/B] and be freely moved and steered
manually on the transport wheels.
Do not roll the machine in this manner on a
ramp!
4. Roll the machine until the milling rotor is posi­
tioned over the surface to be milled.
Risk of injury from rotating milling rotor and
lowering machine!
Make sure that no one can enter the machine's
danger zone during operation.
Proceed with the greatest care and caution!
5. Press the release pedal [15, Fig. B] down.
The 2 transport wheels [11, Fig. A/B] swivel up.
The machine was lowered on the drive
wheels [13, Fig. A/B].
As soon as the machine is switched on or
started, the milling rotor starts turning! The
forward drive and the milling rotor drive cannot
be switched independently of each other.
Risk of damage and injury from uncontrolled
movement of the machine!
19