Dahlert DT-SJ-19 Bedienungsanleitung Seite 22

22
BEFORE REQUESTING FOR REPAIR
Check the following before asking for repair.
For follow-up service and any inquiry you may have while using the product, please contact our Customer Center.
Check the manufacturer's number or the number under the barcode when requesting for follow-up service or parts.
1. I hear 'click' sound
when I start the When the screw fits into the motor, they produce this sound. This has not effect on use.
machine.
2. I hear 'squeak-
This is produced by the friction between screw packing and chamber. This is normal.
squeak' sound.
3. The main body
Make sure the chamber set and main body are assembled properly.
will not work on its
Make sure the power is turned off when assembling / disassembling the product.
own.
4. Please align Make sure they are assembled in accordance with the assembly guide.
safety sensors. Make sure the power is turned off when assembling / disassembling the product.
Check if the power cord is
connected properly.
Check if the hopper is fit
5. It will not work.
properly.
Check if this product is properly
assembled in the assembling
order.
6. The appliance Have you in heavy loads or
stops during large pieces of ingredients into
normal operation. the appliance?
The screw has crack mark and scratch marks on the top. In addition to the straight molding
7. Screw has crack
marks on the top and sides of the screw, it also has a curved mark, all of which were made
or scratch marks.
when molding the screw. This is normal and has no impact on use.
8. The juice leaks
from the outlet Depending on the ingredients used, the juice may come out of the pulp outlet. This is not a defect
immediately but is caused by the characteristic of the ingredient, and the leakage ill stop when the machine
after I insert the runs. If the juice comes out persistently, contact the Customer Center.
ingredients.
Did you put too much ingredients?
If the juice continues to leak from
the top of the main body, contact our
9. The juice leaks from
Customer Center for consultation.
the top of the main
body.
Is the chamber packing
assembled properly?
There may be much pulp
remaining inside.
10. The hopper will
not open.
Did you put foreign or solid
matter (hard seed such as the
seed of persimmon)?
The machine may wobble slightly by the kinetic energy of the motor of the main body. Extracting
juice from various ingredients can cause various degrees of movements depending on the
11. The chamber
characteristics of the ingredients (hard or tough). This is a normal as the movement is caused
is shaking (when
by the rotating screw and is not considered as a trouble. It may seem that it is wobbling more
extracting).
severely when extracting juice from hard ingredients (i.e. carrot/potato/radish/beet/kohlrabi,
etc.) compared to when extracting from soft and watery ingredients.
12. Pulp is
discharged
The pulp is discharged naturally even when you close the lever. Discharging amount and rate
even when the
may vary depending on the ingredients used.
discharge cover is
closed.
4DC01742 사용설명서 DT-SJ-19(102-A2) 7개국어_V.00.indd 22
The machine may not work after a prolonged use (30 minutes
or longer). The machine will work normally after the main body
(motor) cools down.
The machine will not work if the hopper is fit properly. It will
work only when the lock icon on the chamber is matched with
the triangle icon on the lid.
Refer to assembly guide P. 12~16
Refer to p. 17 of the manual and follow the guideline for using
[REV] button.
If the input is greater than the chamber's capacity, the juice may
leak between hopper and chamber. When you are extracting
a large amount, make sure you open the lever and juice cap as
often as necessary to discharge the content inside. If there is any
water or juice on the main body, wipe it off immediately.
The juice will leak if the chamber packing is placed in a wrong
direction or is not tightly placed. Check if the chamber packing is
placed properly.
If the remaining pulp is discharged by turning on the machine,
or the machine is rotated in reverse for 10 seconds two or three
times, the hopper will open smoothly.
If foreign or solid matter is put into the chamber, running
reverse can further the damage. Contact our Customer Center
to request for repair service.
2019-08-13 오후 6:28:12