Operation And Use - Niko 350-20085 Gebrauchsanleitung

Light level 20 50
Number of times
that the red status 1 2
LED flashes
Finally, the red LED will once again flash three times to indicate the switch-off delay.
Switch-off delay puls
Number of times that the
1
red status LED flashes
Please check section 4 to change the mini detector's settings
4. IR REMOTE CONTROL UNIT
You use the IR remote control unit (Fig. 5) to select another application, to perform a test or to enter other
parameters.
4.1. Settings keys
To change the mini detector settings:
1. Press Lock/ three times within five seconds to unblock the device. App. App. Light
unlock Auto Active On/Off
20 50 100 200
The green status LED flashes twice by way of confirmation. The device is now in the settings mode.
Lux Lux Lux Lux
300 400
2. Change the light level or the switch-off delay using the keys below. The red LED will flash to confirm that Learn actual lux
Lux Lux
the motion detector has received the signal from the remote control.
500 700 1000 No
Lux Lux Lux Lux
3. Press Lock/ once to re-block the device. App. App. Light
unlock Auto Active On/Off
Pulse 2min 5min 10min
Time
20 50 100 200
The green status LED flashes twice by way of confirmation. The changed setting is activated, and the
Lux Lux Lux Lux
8
15min 30min 60min
Hours
device works again according to the newly selected settings.
300 400
Learn actual lux
Lux Lux
Memory Memory Clear
Status
in out memory
Note: If you do not block the device, it will be blocked automatically after one minute. All changes are
500 700 1000 No
then automatically saved.
Lux Lux Lux Lux
Test Short Long Fact.
On/Off push push setting
Key Function
Pulse 2min 5min 10min
Time
Use this key to set the mini detector for use as a presence detector.
Lock/ App. App. Light
8
15min 30min 60min
unlock Auto Active On/Off
Hours
Lock/ App. App. Light
Use this key to set the mini detector for use as an absence detector.
Memory Memory Clear
20 unlock Lock/ 50 Auto 100 Active 200 On/Off
App. App. App. App. Light Light App. App. Light Status
in out memory
Lux Lux Lux Lux
Auto unlock Active Lock/ On/Off Auto App. Active App. On/Off Light
Auto Active On/Off
unlock Auto Active On/Off
20 50 Test 100 Short 200 Long Fact.
- Use these red keys to set the desired light level (lux value).
Lux Lux On/Off Lux push Lux push setting
300 50 100 20 200 50 100 400 200
50 100 200
Learn actual lux
Lux Lux Lux Lux 20 Lux Lux 50 100 Lux Lux Lux 200
Lux Lux Lux
Lux Lux Lux Lux
- There are ten fixed lux values: 20, 50, 100, 200, 300, 400, 500, 700,
300 400 1000 lux and No lux (daylight dependent).
Lock/ App. App. Learn actual lux Light
500 700 300 Lux 1000 400 No Lux 400
400
unlock Auto Active On/Off
Learn actual lux Learn actual lux
Learn actual lux
Lux Lux 300 Lux Lux 400
Lux Lux Lux Lux
Learn actual lux
Lux Lux
500 700 1000 No
20 50 100 200
Lux Lux Lux Lux
700 1000 500 700 No 1000 No
700 1000 No
Pulse Lux 2min Lux 5min Lux 10min Lux
Lux Lux Lux 500 Lux 700 Lux 1000 Lux Lux No
Lux Lux Lux
Lux Lux Lux Lux
Time
- Use this key to set the current light level in the room as the level at
300 Pulse 2min 5min 400 10min
Learn actual lux
8
15min Lux 30min 60min Lux
2min Pulse 5min 10min 2min 5min 10min which the lighting must be switched on.
2min 5min 10min
Hours
Pulse 2min 5min 10min
Time
Time Time - When you press this key, the red status LED flashes once to indicate
Time
Time
8
Lock/ App. App. Light
500 15min 700 30min 1000 60min No
8 Hours 8 that the current light level has been loaded. If this light level is not
Memory Lock/ Memory unlock App. Clear Auto App. 8 Active Light On/Off
Lux Lux Lux Lux
30min 15min 60min 30min Status 60min
30min 60min
8
unlock in Auto out memory Hours Active Hours On/Off Hours
15min 30min 60min
Hours
between 20 and 1500 lux, the minimum level (20 lux) or the maximum
Memory Memory Clear
20 50 100 200
Status level (1500 lux) is loaded.
App. Light
Pulse 2min 5min 10min
Memory Test 20 Memory Short Clear Lux 50 in Memory Long Lux 100 out memory Fact. Clear 200 Lux Lux
Memory Clear
Active On/Off Status Status
Status
On/Off Lux out Memory memory push Lux in Memory push Lux out setting memory Clear Lux
out memory
Status
in out memory
Time
Test 300 Short Long Fact. 400 Use this setting when the desired minimum light level in the room has
8
Learn actual lux
15min 100 30min 200 60min
Short On/Off Long Test Short push Fact. push Long setting Fact.
Short 300 Long Lux Fact. 400 Lux
Hours
Learn actual lux
Lux Lux
push Lux On/Off push Test setting Short push push Lux Long setting Fact.
push push setting
been reached. This is the time at which the lighting must be switched on
On/Off push push setting
because the daylight level is no longer adequate.
500 700 1000 No
Memory Memory Clear
400
Status
500 700 Lux 1000 Lux No Lux Lux
actual lux
in out memory
Lux
Lux Lux Lux Lux
- Use these blue keys to set the desired switch-off delay.
Test Short Long Fact.
1000 Pulse No 2min 5min 10min
On/Off push push setting
Pulse 2min 5min 10min
Lux Lux
- There are six fixed values: 2, 5, 10, 15, 30 and 60 minutes.
Time
Time
8
15min 30min 60min
Hours
5min 10min 8
15min 30min 60min
Hours
Time Lock/ App. App. Light
unlock Auto Active On/Off If you press this key:
Memory Memory Clear
8 Status
in out memory
Memory 60min Memory Clear
Hours Status - The lighting remains switched on permanently for eight hours.
in out memory
20 50 100 200
- The red status LED flashes (0.25 s on and 30 s
Lux Lux Lux Lux
Test Short Long Fact.
Clear
Lock/ Test On/Off Short App. App. Long push Fact. Light push setting off).
Status
memory
On/Off push push setting
unlock Auto Active On/Off
- All other functions on the mini detector are blocked.
300 400
Learn actual lux
Lux Lux
Long Fact.
20 50 100 200
push setting
Lux Lux Lux Lux
Press this key again to deactivate the function. The red status LED stops
500 700 1000 No
Lux Lux Lux Lux
flashing. The mini detector is returned to automatic mode. You can now
App. App. Light
App. 300 Light 400
Learn actual lux
Auto Active On/Off
Lux Lux
Active On/Off
switch on the lighting again according to the selected application.
Pulse 2min 5min 10min
50 100 200
500 100 200 700 1000 Time No
Lux Lux Lux
Lux Lux Lux Lux Lux Lux You cannot switch off this function using a push button.
8
15min 30min 60min
Hours
400
400
Learn actual lux
Pulse 2min 5min 10min
actual lux
Lux
Lux
With this button you can store the most recently selected settings (light
Memory Memory Clear
Time
Status
in out memory level and switch-off delay that were last set) into the memory of the IR
700 1000 No
8
1000 No
15min 30min 60min
Lux Lux Lux remote control.
Hours
Lux Lux
Test Short Long Fact.
On/Off push push setting
Press this key to send the saved settings to the mini detector.
Memory Memory Clear
2min 5min 10min
5min 10min
Status
in out memory
Time
Time
This key is handy for setting the same parameters on various mini
8
Test Short 8 Long Fact.
30min 60min
60min
Hours detectors simultaneously.
Hours
On/Off push push setting
This key erases all settings from the memory of the IR remote
Memory Clear
Clear
Status
out memory Status
control unit.
memory
The device is returned to the factory settings.
Short Long Fact.
Long Fact.
push push setting
push setting
PM350-20085R15331
100 200 300 400 500 700
3 4 5 6 7 8
2 min 5 min 10 min 15 min
2 3 4 5
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
Pulse 2min 5min
Time
15min 30min 60min
Memory Memory Clear
in out memory
1000 ∞ Learn
Test Short Long
On/Off push push
9 10 11
Lock/ App. App. Light
unlock Auto Active On/Off
20 50 100 200
Lock/ App. App. Light
Lux Lux Lux Lux
unlock Auto Active On/Off
300 400
Learn actual lux
20 50 100 200
Lux Lux
Lux Lux Lux Lux
30 min 60 min
500 700 1000 No
300 400
Lux Lux Lux Lux
Learn actual lux
Lux Lux
6 7
Pulse 2min 5min 10min
500 700 1000 No
Lux Lux Lux Lux
Time
Lock/ App. App. Light
8
unlock Auto 15min Active 30min On/Off 60min
Pulse 2min 5min 10min Hours
Time
20 50 100 200
Memory Memory Clear
Lux Lux Lux Lux
8 Status
in out memory
15min 30min 60min
Hours
300 400
Learn actual lux
Test Short Long Fact.
Lux Lux
Memory Memory Clear
On/Off push push setting
Status
in out memory
500 700 1000 No
Lux Lux Lux Lux
Test Short Long Fact.
On/Off push push setting
Pulse 2min 5min 10min
4.2. Function keys
Time
8
Key
15min 30min 60min
Hours
Memory Memory Clear
Status
in out memory
Test Short Long Fact.
On/Off push push setting
Lock/ App. App. Light
unlock Auto Active On/Off
20 50 100 200
Lux Lux Lux Lux
300 400
Learn actual lux
Lux Lux
500 700 1000 No
Lux Lux Lux Lux
Pulse 2min 5min 10min
Time

5. OPERATION AND USE

8
15min 30min 60min
Hours
5.1. Initial use
Memory Memory Clear
Status
in out memory
Only attach the mini detector to a power supply after all of the cables have been connected. The mini detector
is ready for use approximately 40 seconds (warm-up time) after you have switched on the power supply.
Test Short Long Fact.
On/Off push push setting
While the device is warming up, the red indication LED will flash (0.25 s on and 2 s off) and the load will be
switched off for 40 s. Once the device is warmed up, the green status LED flashes twice in rapid succession.
5.2. General operation
The integrated light sensor continuously measures the daylight level in the detection area and compares this
level to the preset lux value. Thanks to the light sensor, the light switches on automatically only if the mini
detector detects motion within the detection range and if there is insufficient daylight present:
• The lighting remains switched on as long as motion is detected and as long there is insufficient
daylight present in the room.
• After the last motion is detected, the lighting remains switched on for the duration of the
preset switch-off delay (1 to 60 minutes). As soon as the switch-off delay has elapsed, the
lighting switches off.
• The lighting also switches off automatically as soon as the level of daylight is sufficiently high,
even if at that moment there is still motion detected in the room.
5.3. Detection range
You can expand the detection range by connecting two mini detectors (350-20085) in parallel (master-master
arrangement) (also see Fig. 1). These mini detectors each control the lighting according to their own settings.
They have the same detection range (circular with a diameter of 9.5 m). In order to cover an entire area with
several detectors, we recommend that you take into account an overlap of approximately 30% (Fig. 6). In the
case of a master-master arrangement, the mini detectors function optimally in rooms with little or no daylight.
5.4. Examples of applications
Example 1: Attic
Operation of the absence detector:
• The lighting is automatically switched off, after a preset time period (switch-off delay), if the mini
detector does not detect any more motion in the detection range or if the ambient light level exceeds the
preset lux value for a period of five minutes.
• You can only switch on the lighting again manually by briefly pressing the push button. If there is sufficient
light in the room, the lighting will however not be switched on by a short push on the button. You can also
manually switch off the lighting (= eco-off).
• In addition, you can also press and hold the push button, which is recommended in situations when the
lighting must be switched on or off for longer periods of time:
10min
Lock/ App. App. Light
unlock Auto Active On/Off
8
Hours
20 50 100 200
Lock/ App. App. Light
Lux Lux Lux Lux
unlock Auto Active On/Off
Status
300 400
20 50 100 200
Learn actual lux
Lux Lux
Lux Lux Lux Lux
The detection range is tested by activating the integrated motion sensor by
Fact.
setting
way of a walking test:
500 700 1000 No
300 400
Learn actual lux
Lux Lux Lux Lux
Lux Lux
- The lighting is switched on for five seconds, and the red status LED
flashes when the test mode is activated.
500 Pulse 700 2min 1000 5min No 10min
Lux Lux Lux Lux
- The lighting is switched on for five seconds, and the red status LED
Time
flashes every time the sensor detects activity.
8
15min 30min 60min
Pulse 2min 5min 10min Hours
Time
The test mode is closed in one of the following ways:
Memory Memory Clear
8
Status
15min 30min 60min
in out memory
Hours
• Press Test on the IR remote control unit. Short Long Fact.
Memory Memory Clear
Status
On/Off push push setting
in out memory
• Press on the IR remote control unit.
Test Short Long Fact.
On/Off push push setting
• Briefly press the connected push button.
After this, the mini detector will again work according to the selected
settings.
During the walking test, the light sensor does not work.
This button gives the same result as a short push on the connected push
button (see section 3.2.).
This button gives the same result as a long push on the connected push
button (see section 3.2.).
Function
If you press this key, the device indicates what the current settings are by
way of the red status LED. The green status LED indicates the start status.
First, the green status LED flashes, and then the red status LED indicates
the status. The first time that the red status LED flashes, it indicates the
Lock/ App. App. Light
unlock Auto Active On/Off
preset light level. The second time it indicates the switch-off delay (see
section 3.3.).
20 50 100 200
Lux Lux Lux Lux
For example: The mini detector is set to 300 lux and 10 minutes. Press
300 400
Learn actual lux
Lux Lux
insert symbol: the green status LED flashes once and the red status LED
five times (= 300 lux), then the green status LED flashes once more and the
500 700 1000 No
Lux Lux Lux Lux
red status LED flashes four times
(= 10 min).
Pulse 2min 5min 10min
You switch the light on or off permanently, regardless of the motion
Time
detected or the light level. If this function is activated, the red status LED 8
15min 30min 60min
Hours
flashes (0.25 s on and 10 s off).
Memory Memory Clear
Status
in out memory
The mini detector will remain in this function mode until you either:
• press Test Short once Long Fact.
On/Off push push setting
• press the connected push button briefly
• press three times within 5 s.
Lock/ App. App. Light
unlock
Auto Active On/Off
After this, the mini detector will again work according to the selected
settings. The red status LED flashes once by way of confirmation.
20 50 100 200
Lux Lux Lux Lux
300 400
Learn actual lux
Lux Lux
500 700 1000 No
Lux Lux Lux Lux
Pulse 2min 5min 10min
Time
8
15min 30min 60min
Hours
Memory Memory Clear
Status
in out memory
Test Short Long Fact.
On/Off push push setting
350-20085
9
EN